Trio JR240 User Manual Download

Page: 72 / 76

Issue 09-10

J Series

900MHz and 2

GHz Spread Spectrum Ethernet Radio

Modem

RF Channel Data Rate:

900MHZ version - 512kbps or 256kbps
2.4GHz version - 256kbps

Bit Error Rate:

256kbps : < 1x10-6 @ -102 dBm
512kbps : < 1x10-6 @ -92 dBm

Collision Avoidance:

TRIO Datacom’s unique
ChannelShare™ collision avoidance
system

Radio

Frequency Range:

902-928MHz or 2.4-2.483GHz
Region Specific Versions Available

Tx Power:

User configurable

(900Mhz) 0.01 to1W (+30dBm) in 0.5dB
steps.

(2.4Ghz) 0.01 to 0.5W (+27dBm) in
0.5dB steps.

Protection:

TX over-temperature and

reverse power protection (VSWR
900Mhz only)

Modulation:

4 Level GFSK

Local regulatory conditions may determine the
performance and suitability of individual versions
in different countries. It is the responsibility of
the buyer to confirm these regulatory conditions.
Performance data indicates typical values related
to the described unit.

Information subject to change without notice.
© Copyright 2009 TRIO Datacom Pty Ltd. All rights
reserved. Issue 10-2009

• Export restrictions may apply

Note: Not all product features are available

in every mode of operation.

Network Management

Configuration:

All configuration

via embedded HTML interface
(HTTP, HTTPS & console)
Diagnostics:

Compatible with TRIO

Datacom TVIEW+ Diagnostics for

stand alone network management

Firmware:

Local and Remote

Field upgradable Flash memory

Interface

Ethernet:

Dual RJ-45 Bridging

IEEE 802.3 Ports with MDI/MIDX

(auto-detecting) interface

Serial:

DB-9 Female - 2 x 3-wire

TxD/RxD RS-232 Serial Ports
plus CTS/RTS

Configuration Port:

Either Ethernet

Port can be used for diagnostics,
configuration and re-programming

Antenna:

Dual TNC female bulkhead.

Separate connectors for LinkXtend™

or separate TX/RX antennas.

Power:

2 pin locking, mating

connector supplied

LED Display:

Multimode

Indicators for Pwr, Tx, Rx, Sync,
LAN 1 & LAN 2 (Link and Act)

Ethernet

Ethernet Ports:

Dual 10/100

Mbps (auto-sensing) compliant

with IEEE 802.3

Protocols:

Ethernet/IP (including

UDP, TCP, DHCP, ARP, ICMP, STP,
IGMP, SNTP & TFPT)

Terminal Server:

Legacy RS-232

serial support via embedded terminal

servers (UDP/TCP).

DHCP Modes:

Auto and Manual

NTP:

SNTP Client/Server Time

Synchronization Support

Security

Encryption:

256-bit AES encryption*

HTML Interface:

HTTPS Password Protected

Trusted Unit:

Optional Trusted Access

point-Trusted Remote operation.

General

Temp Range:

-40 to + 70ºC

Humidity:

95% @ 40ºC

(104ºF) non-condensing

Power Supply:

10-30 Vdc

(13.8 Vdc nom)

Transmit Current:

(900MHz)

800mA nom @ 1W

(2.4GHz) 800mA nom @ 0.5W

Receive Current:

<150mA nom

Dimensions:

Rugged Diecast Enclosure

100 x 34 x 165mm
(4.0 x 1.4 x 6.5 inches)

Mounting:

Integrated Mounting Holes

Weight:

0.5kg (1.1lbs.)

Compliances

900 MHz Version

FCC

PART 15

RSS210

ACA

AS/NZS 4268

Hazardous Environment Certification

CSA Class I, Division II

2.4GHz Version

FCC

PART 15

RSS210

ACA

AZ/NZS 4268

ETSI

EN 60950

EN 50392

EN 300 328

EN 301 489

Hazardous Environment Certification
ATEX II 3G nA IIC T4

This device is an open type equipment that must be used

within a suitable end-use system enclosure, the interior

of which is accessible only through the use of a tool. The

suitability of the enclosure is subject to investigation by the

local Authority having jurisdiction at the time of installation.

All TRIO Datacom Radios come with a industry leading 3 year Warranty

For more information please go to:
www.triodatacom.com

Summary of Contents for JR240













































































Search results

Summary of Contents for JR240

Reviews:

Related manuals for JR240

Brands by name

Popular brands

Trio JR240, User Manual

Search results

Summary of Contents for JR240

Reviews:

Related manuals for JR240

Brands by name

Popular brands