Trio JR240 User Manual Download Page 2

Page: 2 / 76

Page 2

J-Series Data Radio – User Manual

Issue 09-10

Part F – Quick Reference Guide

Introduction 34
Mounting and Installation Instructions

Physical Dimensions - Remote Ethernet Data Radio

Connecting Antennas and RF Feeders

J-Series Connections Layout

Power Supply Requirements

Communication Ports

Cable Termination

Serial Port A & B Ports

LED Indicators

J-Series Configuration (Web Interface)

Resolving Ethernet Configuration Problems

Multi Master Synchronisation

Text User Interface (TUI)

Spectrum Analyzer

SNMP

eDiagnostics

Part G – Quick Start Guide

Point to Point Ethernet Link Setup

Point to Point - TCP Serial Device Server Setup Guide

Point to Point - UDP (Unicast) Serial Device Server Setup Guide 58
Point to Multi-Point - UDP (Multicast) Serial Device Server Setup

Guide 59

Point to Multi-Point with Peer to Peer - UDP (Multicast to Multicast)

Serial Device Server Setup Guide

Part H

–

Installation

Commissioning 63

Optimizing the Antenna for Rx Signal

Commissioning

Part I – Firmware Updating

Part J – FCC Approved Antennas

Part K – Support Options

Website Information

E-mail Technical Support

Contents

Part A – Preface

Warranty

Important Notice

FCC Compliance Notices

Australian Compliance Notices

EU (ETSI)

Compliance Notices

Part B – J-Series Overview

Introduction 5
Product Range

Features and Benefits

Ordering Information

Standard Accessories

Part C – Network Types

Introduction

Point-to-Point Networks (PTP)

Point-to-Multipoint Networks (PTMP)

Point-to-Multipoint via KwikStream™ Repeater

Point to Point with LinkXtend™ Bridge (PTP/B)

Point to Multipoint via LinkXtend™ Bridge (PTMP/B)

Part D – Features

Features Useful for Optimizing Performance.

Multi-Access Point Synchronization

Digital Collision Avoidance

Retries and Retransmissions

Ethernet Traffic Filtering

Security 18
SmartPath™ 20
Diagnostics Tools

Text User Interface (TUI)

Spectrum Analyzer and Channel Lockout Facility

Legacy Serial Support

Part E – RF Planning and Design

Understanding RF Path Requirements

Examples of Predictive Path Modelling

Antennas

RF Feeders and Protection

Band Pass Filter (900MHz Only)

Summary of Contents for JR240













































































Search results

Summary of Contents for JR240

Reviews:

Related manuals for JR240

Brands by name

Popular brands

Trio JR240, User Manual

Search results

Summary of Contents for JR240

Reviews:

Related manuals for JR240

Brands by name

Popular brands