Trio JR240 User Manual Download Page 5 | Manualshive

Page: 5 / 76

background image

Page 5

J-Series Data Radio – User Manual

Part B – J-Series Overview

Introduction

The advanced TRIO Datacom J-Series frequency hopping Ethernet

Data Radio sets the standard for professional high speed serial

data communications in the license free 900MHz and 2.4GHz

bands.
With maximum range and virtually unlimited system coverage due

to its unique LinkXTend™ network bridging and KwikStream™

high speed repeater capabilities, the industrial strength J-Series is

ideally suited for the most demanding point to multipoint and point

to point wireless SCADA and Telemetry applications.
The highly versatile J-Series also offers dual Ethernet ports with

TRIO TVIEW+ network wide diagnostics compatibility.

Product Range

The TRIO J-Series comprises of the following models:

- the JR900, which operates within the 915MHz license

free frequency band (country specific models apply),

and

- the JR240 that can be configured for use in the

2.4GHz license free bands available throughout the

world.

Part B – J-Series Overview

J-Series Ethernet Data Radio

Features and Benefits

Outstanding and highly versatile operational

capability:

• Point to point and point to multi-point operation
• Configurable personality – access point-remote-bridge-repeater
• KwikStream™ high speed single radio repeater mode *
• Unlimited coverage networks
• No restriction on the number of radios in any system
• Unique dual antenna LinkXtend™ technology increases

usable range

• Repeater and Bridge units support locally connected user

devices

• ChannelShare™ collision avoidance for unsolicited

remote transmissions allowing simultaneous polling and

spontaneous reporting

* Up to 140km (90 miles) single repeater system range with

6dB antennas (900MHz)

A Radio and Modem that extends performance

boundaries:

• License free operation in 900MHz & 2.4GHz ISM frequency

bands

• 512k high speed over-air data rate [900MHz version only] (can

be reduced to 256k for longer range)
• Robust, frequency hopping spread spectrum technology for

superior interference immunity
• Ultra Long Range high performance receiver *
• 1 Watt maximum allowable transmitter power (900MHz version

only)
• Advanced error free data delivery with CRC plus selectable

FEC and ARQ

• Multi-Access Point synchronization mode for interference

reduction with co-located Access Point radios

• High VSWR protection (900MHz version only)
* Up to 70km (45 miles) maximum single hop line-of-sight range

with 6dB antennas (900MHz)

«
...
3
4
5
6
7
...
»

Summary of Contents for JR240













































































Reviews:

No comments

Related manuals for JR240

Brand: JBL Pages: 25

Brand: Hytera Pages: 22

Brand: Raveon Pages: 43

Brand: Philco Pages: 7

Brand: Com-Net Ericsson Pages: 20

Brand: Sencor Pages: 10

Brand: Vitek Pages: 6

Brand: Banner Pages: 2

Brand: Datalogic Pages: 40

Brand: Eton Pages: 40

Brand: PRESIDENT Pages: 44

Brand: Vertex Standard Pages: 40

Brand: GEM Pages: 18

Brand: GE Pages: 12

Brand: Sony Pages: 2

Brand: Sony Pages: 2

Brand: Sony Pages: 2

SRF-M95 walkman

Brand: Sony Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands