Trio JR240 User Manual Download | Manualshive

Page: 29 / 76

background image

Page 29

J-Series Data Radio – User Manual

Legacy Serial Modes Supported

Point to Point via TCP/IP:
This mode of operation provides a reliable point to point connection between two units (based on the IP address). When only two units need serial

connectivity in a PTP arrangement and latency and bandwidth are not a major concern, the TCP IP mode should be selected.
For the purposes of clarity, a PTP radio network is shown in the diagram above. However, a PTP Serial Data link via TCP/IP can be established

between any two radio units in the network, regardless of the type of radio network actually implemented (i.e.: PTMP or PTMP with Bridges).

Refer to Part G of this User Manual for more information.

Point to Point via UDP/IP:
This mode of operation provides a point to point connection between two units (based on the IP address). This mode of operation is best suited to

high speed serial protocols which need low latency and high bandwidth. Refer to Part G of this User Manual for more information.

«
...
27
28
29
30
31
...
»

Summary of Contents for JR240













































































Reviews:

No comments

Related manuals for JR240

Brand: Olympia Pages: 72

Brand: Escort Pages: 28

Brand: Radio Shack Pages: 10

EDDINGTON EDD-DAB-BLK

Brand: MAJORITY Pages: 26

Brand: Sangean Pages: 15

Brand: GPX Pages: 4

Brand: Denver Pages: 29

Brand: Lafayette Pages: 38

Brand: Acoustic Research Pages: 20

Brand: Tres Pages: 18

Brand: Icom Pages: 16

microTALK CXR950

Brand: Cobra Pages: 17

MICROTALK CXR925C

Brand: Cobra Pages: 18

MICROTALK CXR825C

Brand: Cobra Pages: 17

Brand: Ericsson Pages: 34

VHF 110 AIS series

Brand: Garmin Pages: 4

Brand: Garmin Pages: 22

Brand: Garmin Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands