manualshive.com logo in svg

Trio JR240, User Manual

Share
Download
Trio JR240 User Manual Download Page 39

Page  39  

J-Series Data Radio – User Manual

(1) Pwr/TX - DC Power & TX LEDs

If all the LEDs are off, no DC power is reaching the radio modem or the internal fuse is open. Successful power-up is indicated by the Pwr/Tx LED 

showing a continuous GREEN state for Remotes or an alternating Red/Green for Access Points.
Tx Indicator (Tx) : When the transmitter is active the Pwr/Tx LED is in a RED state.
Note: The J-Series radio will take approximately 45 seconds to boot up - during this time, the DC power LED will remain solid green and various 

LED activity may occur. Please wait at least 45 seconds before attempting to use radio. 

(2) Sync/No RX - Synchronisation and No Received Signal LEDs  

A regular flashing GREEN Sync/No RX LED indicates that the modem is synchronised to its Access Point. The Sync/No RX LED will also flash 

GREEN when the modem is receiving data. 
A regular flashing RED Sync/No RX LED indicates the REMOTE is not synchronised to an Access Point or BRIDGE. Check the antenna, all RF 

connections and the radio configuration. Some common causes of this error is that the Subnet ID may not match the Access Point or there may be 

insufficient RX signal or too much interference.

(3) & (4) LAN 1 & LAN 2 - LAN Link and Activity LEDs 

The Green Link and Amber Activity LEDs  indicate Ethernet status on the two LAN ports. These LEDs will show solid Green when an Ethernet Link 

is established and will flash Amber to indicate Ethernet data transmission is occurring. 

(5) TxD/RxD - Serial TxD/RxD LEDs 

The RxD/TxD LEDs  indicate data flow into/out of the user port. Data being sent to the port for transmission is indicated by a RED flash, and data 

being received over the air and then forwarded to the serial port is shown as a GREEN flash.

Firmware Updating and Factory Default Information LEDs

In some circumstances a firmware update or factory default might be required. A special LED sequence is shown during this phase.

Pwr 

/ 

Tx

Sync 

/ 

NoRx

Link 1 

/ 

Activ 1

Link 2 

/ 

Activ 2

RxD 

/ 

TxD

Firmware upgrade

Amber

Amber

Amber

Amber

Amber

Factory Defaults

Green

Green

Green

Green

Green

Firmware Upgrade : All LEDs flash AMBER (as shown in table above) - 1 second ON and 1 second OFF
Factory Default : Factory Default LEDs (as shown in table above) are permanently GREEN during factory default reset. 

Error LED Indications

In some circumstances the radio will indicate an error state. This is shown as all LEDs flashing RED for 1 sec and then a pattern of green LEDs for 

1 sec. The pattern of green LEDs indicate the type of error. Please consult the table for more information. 

Pwr 

/ 

Tx

Sync 

/

 

NoRx

Link 1  

/ 

Activ 1

Link 2 

/ 

Activ 2

RxD 

/

 

TxD

Problem

High VSWR

Green

Green

Ant 1 or 2 has high VSWR

High Temperature

Green

Green

Green

Internal Temperature too high

DC Voltage out of Spec

Green

Green

Green

Green

DC Voltage Out of Spec

For all other patterns of error LEDs the radio must be returned to the factory for repair.  

LED Indicators

Part F – Quick Reference Guide

Summary of Contents for JR240













































































Reviews:

No comments

Brands by name

Popular brands

Load more brands