manualshive.com logo in svg

Trio JR240, User Manual

Share
Download
Trio JR240 User Manual Download Page 61

Page  61  

J-Series Data Radio – User Manual

Point to Multi-Point with Peer to Peer - UDP (Multicast to Multicast) 

Serial Device Server Setup Guide

Introduction

Point to Multi-Point (PTMP) with Peer to Peer connectivity using 

the UDP mode of the embedded J-Series terminal servers is useful 

for PTMP serial links requiring peer to peer connectivity.  
More information on PTMP Serial with Peer to Peer via UDP 

(Multicast to Multicast) can be found in Part D of this user manual. 

 

The following information will guide you through the minimum 

steps required to configure this feature in the J-Series. Refer to the 

HTML  programmer for more information about each item.
Please ensure you have already configured the J-Series radios for 

PTMP mode as described in this manual (Alternatively you can use 

the PTMP wizards).  Ensure you have configured the units with the 

IP addresses as specified in the diagram above. 
Ensure the Default Gateway in the Network Parameters 

configuration of all radios is configured as shown. 

1 - Configuration (Unit A)

Connect your browser to the J-Series configuration web page of 

Unit A (192.168.2.16) and select to the “Configuration” page and 

then select the “Serial Port A” option.
(a) Ensure the Mode is configured to be “Serial Device Server”
(b) Ensure the Character Layer matches the configuration of the 

external serial device you are connecting to the J-Series Serial 

Port. The default is 9600,8,N,1.
(c) Ensure the Packet Layer is set to “Standard”
(d) Ensure the Protocol is configured to be “UDP”
(e) Ensure the Network Type is configured to be “Multipoint to 

Multipoint”

(f) Ensure the Local IP Address is an address from the designated 

multicast range of IP Addresses, in this example we are using 

224.140.1.1 (this is the multi-cast address as configured in the 

multi-point units B & C. In this mode, all the multi-cast IP addresses 

are the same)
(g) Ensure the Local IP Port is configured to be 30010 
(h) Ensure the Remote IP Address is an address from the 

designated multicast range of IP Addresses, in this example we 

are using 224.140.1.1 (this is the multi-cast address as configured 

in the multi-point units B & C. In this mode, all the multi-cast IP 

addresses are the same)
(h) Ensure the Remote IP Port is configured to be 30010 
(i) Ensure the Time to Live is configured as “Restrict to same 

Subnet”
Click on Activate Configuration.
Once the web browser has activated the new configuration and 

then returned to the Configuration page, the configuration of Unit A 

is now complete. The next step is to configure the Multi-point Units 

B & C. 

2 - Configuration (Units B&C)

Repeat the steps as shown above in “1 - Configuration (Unit A)” 

with the exception of default Gateway Address as found in the 

“Configuration -> Network Parameters” 
The Default Gateway IP address should be the IP address of 

your Gateway in the network. In this example, the Access Point IP 

address is defined as the Gateway (192.168.2.16).

Part G –   Quick Start Guide

Summary of Contents for JR240













































































Reviews:

No comments

Brands by name

Popular brands

Load more brands