manualshive.com logo in svg

Tridonic DALI MSensor 02, Product Manual

Share
Download
Tridonic DALI MSensor 02 Product Manual Download Page 4

&nbsp Scope of documentation

Documentation DALI MSensor 02 | 02-2012 | en

- 4 / 38 -

Validity

These operating instructions are valid for the DALI MSensor 02. For better distinction from previous versions the DALI

MSensor 02 carries imprints with the information "Version 02" or "Firmware version V2.00".

Notice

The DALI MSensor 02 behaves differently to previous versions (V1.5 and earlier). The DALI MSensor is

therefore only backward compatible to a limited extent. 

Please pay attention to notes in the individual chapters! 

For version V1.5 or earlier sensors: pay attention to the notes in the respective documentation!

The DALI MSensor 02 is configured in the masterCONFIGURATOR software (V2.02. or later). Using older

versions of the software to configure the DALI MSensor 02 will result in incorrect operation. 

Please make sure you are using an up-to-date version of the masterCONFIGURATOR software.

TRIDONIC GmbH & Co KG is constantly striving to develop all its products. This means that there may be changes in form,

equipment and technology.

Claims cannot therefore be made on the basis of information, diagrams or descriptions in these instructions.

The latest version of these operating instructions is available on our home page at

http://www.tridonic.com/com/en/operating-instructions.asp

Version information

Editorial deadline:

24-02-2012

Version number:

1.0

Issue date:

24-02-2012

Copyright

This documentation may not be changed, expanded, copied or passed to third parties without the prior written agreement of

TRIDONIC GmbH & Co KG.

We are always open to comments, corrections and requests. Please send them to 

.

[email protected]

Imprint

Tridonic GmbH & Co KG

Färbergasse 15

6851 Dornbirn

Austria

T +43 5572 395-0

F +43 5572 20176

www.tridonic.com

...

Summary of Contents for DALI MSensor 02







































Reviews:

No comments

Brands by name

Popular brands

Load more brands