manualshive.com logo in svg

Tridonic DALI MSensor 02, Product Manual

Share
Download
Tridonic DALI MSensor 02 Product Manual Download Page 14

&nbsp Constant light control

Documentation DALI MSensor 02 | 02-2012 | en

- 14 / 38 -

Ambient light
control:
"temporarily
disabled"

Light control can be temporarily deactivated by a manual intervention on another DALI controller. Doing

so temporarily switches off light control. The luminaires remain adjusted to the corresponding setpoint.

Light control is reactivated at the next switch-on or by an activation command.

Commissioning

Setting operating modes

The individual operating modes can be set by using the masterCONFIGURATOR software (V2.02 or later) (

see chapter 

 

 "Source directory", page 35

Setting the brightness setpoint

The brightness setpoint is set by using an IR SMART Controller, DALI RC or masterCONFIGURATOR.

Notice

The factory settings of the ambient light sensor are appropriate for normal conditions in a typical office room.

Factors such as the room height, type of furniture and nature of the floor can make it necessary to make

adjustments. 

Check that ambient light control adjusts the lighting to desired levels. 

In case of incorrect operation or unsatisfactory results: adjust the brightness setpoint.

Notice

A suitable brightness setpoint is typically defined by using a lux meter to make a localised brightness

measurement. The results obtained may vary depending where the measurement is made and what the

external lighting conditions are. 

Check ambient light control at various locations within the measuring area and under varying external

lighting conditions. 

Make sure that the selected brightness setpoint takes into account varying conditions.

Procedure with IR SMART Controller

For the names of the buttons with letters, see the figure showing the IR SMART Controller (

see chapter "IR SMART

)

Controller", page 21

Set the desired brightness by pressing the Up/Down button (F and G)

Save the new brightness setpoint by pressing the SET button (C)

-› DALI MSensor 02 briefly dims the luminaire group up and down

Procedure with DALI-RC

For the names of the buttons with letters, see the figure showing the DALI RC (

)

see chapter "DALI RC", page 22

Set the desired brightness by pressing the +/- button (J)

Save the new brightness setpoint by pressing the AUTOMATIC button (K) for at least 3 seconds.

-› DALI MSensor 02 briefly dims the luminaire group up and down

Summary of Contents for DALI MSensor 02







































Reviews:

No comments

Brands by name

Popular brands

Load more brands