manualshive.com logo in svg

Tridonic DALI MSensor 02, Product Manual

Share
Download
Tridonic DALI MSensor 02 Product Manual Download Page 10

&nbsp Commissioning and Adaptions

Documentation DALI MSensor 02 | 02-2012 | en

- 10 / 38 -

Commissioning and settings

The DALI MSensor 02 either controls all the devices on the DALI circuit or a DALI group. To enlarge the presence detection

area, it is possible to assign the same destination to several DALI MSensors 02. To achieve this, simply assign the sensors

to the same DALI group.

The DALI MSensor 02 is configured in the masterCONFIGURATOR software (V2.02. or later). The DALI MSensor 02 can be

assigned to a specific effective range. In addition, the parameters of the individual functions can be individually adjusted (

see

).There are two ways of obtaining assignment to an effective range:

chapter "Functions", page 12

Group assignment by using rotary switch

Group assignment by using masterCONFIGURATOR software

Notice

Luminaires must not belong to more than one DALI group! Otherwise the sensors will not interpret commands

sent to the luminaire correctly. 

Unlike other DALI controllers, a DALI address is assigned to the DALI MSensor 02 during addressing. This

reduces the total number of available DALI addresses. This must be taken into account when designing the

DALI circuit!

Extending an existing DALI circuit

The DALI MSensor 02 can be used in an existing DALI circuit when a system is extended if the DALI

MSensor 02 controls its own group.It is not possible to operate a DALI MSensor 02 and a DALI MSensor

(V1.5 or earlier) in the same DALI group. Because of the modified grouping concept, there is no

synchronisation of constant light control and presence detection between the two equipment generations.

Group assignment by using rotary switch

The effective range of the DALI MSensor 02 is set using the rotary switch at the rear of the sensor. All control gear located

within the previously set effective range is controlled by the sensor.

Rotary switch setting Effective range (group)

0

All (broadcast)

1

0

2

1

3...9

2...8

A...F

9...14

Summary of Contents for DALI MSensor 02







































Reviews:

No comments

Brands by name

Popular brands

Load more brands