manualshive.com logo in svg

Tridonic DALI MSensor 02, Product Manual

Share
Download
Tridonic DALI MSensor 02 Product Manual Download Page 11

&nbsp Commissioning and Adaptions

Documentation DALI MSensor 02 | 02-2012 | en

- 11 / 38 -

Group assignment by using masterCONFIGURATOR

The effective range of the DALI MSensor 02 can be set in the masterCONFIGURATOR software (V2.02 or later). When this

assignment method is used, the position of the sensor's rotary switch is ignored and the assignment selected in the

masterCONFIGURATOR software is active. If the group assignment in the masterCONFIGURATOR software is cancelled,

the assignment set using the rotary switch becomes effective.

Replacing a faulty DALI MSensor (V1.5 or earlier)

It is only possible to replace a faulty DALI MSensor (V1.5 or earlier) by a DALI MSensor 02 if specific preconditions are met:

Make sure that there is no other DALI MSensor (V1.5 or earlier) in the DALI group in question!

Make sure that the faulty DALI MSensor (V1.5 or earlier) is not influenced by other DALI controllers (e.g. by the fact

that a DALI GC activates daylight-based control via the sensor group).

Further adaptation is required in the case other applications:

If you have any queries, please contact Tridonic Technical Support.

Alternatively, it is possible to use the masterCONFIGURATOR software to install the V1.5 firmware in the DALI

MSensor 02. The DALI MSensor 02 will then behave in the same way as previous-generation DALI MSensors.

...

Summary of Contents for DALI MSensor 02







































Reviews:

No comments

Brands by name

Popular brands

Load more brands