TRENDnet TI-G160WS User Manual Download Page 76

Page: 76 / 148

TRENDnet User’s Guide

Industrial Managed Switch Series

Word 0 Hi byte = Port ID.

0x051b

1 word

HEX

Secondary Port of the Xpress-ring2

Word 0 Hi byte = Port ID.

0x051c

1 word

HEX

Role of Xpress-ring1

0x0000 :

Forwarder

0x0001 :

Arbiter

0x051d

1 word

HEX

Role of Xpress-ring2

0x0000 :

Forwarder

0x0001 :

Arbiter

0x051e

1 word

HEX

Primary Port Status of Xpress-ring1

0x0000 : link down

0x0001 : forwarding

0x0002 : blocking

0x051f

1 word

HEX

Secondary Port Status of Xpress-ring1

0x0000 : link down

0x0001 : forwarding

0x0002 : blocking

0x0520

1 word

HEX

Primary Port Status of Xpress-ring2

0x0000 : link down

0x0001 : forwarding

0x0002 : blocking

0x0521

1 word

HEX

Secondary Port Status of Xpress-ring2

0x0000 : link down

0x0001 : forwarding

0x0002 : blocking

CLI Configuration

Node

Command

Description

enable

show modbus

This command displays the current
Modbus configurations.

configure

modbus (disable|enable)

This command disables / enables
the Modbus on the switch.

Web Configuration

Advanced Settings > Modbus

Parameter

Description

State

Select this option to enable / disable the Modbus on the
Switch.

Apply

Click Apply to save your changes to the Switch.

Refresh

Click Refresh to begin configuring this screen afresh.

Summary of Contents for TI-G160WS




















































































































































Search results

Summary of Contents for TI-G160WS

Reviews:

TRENDnet TI-G160WS, User Manual, Page: 76 / 148

Search results

Summary of Contents for TI-G160WS

Reviews: