TRENDnet TI-G160WS User Manual Download Page 11

Page: 11 / 148

TRENDnet User’s Guide

Industrial Managed Switch Series

ALM DIP Switches

Switch

Status

Function

OFF

Disable alarm relay for PWR power input

Enable alarm relay for power failure on PWR power input

OFF

Disable alarm relay for RPS power input

Enable alarm relay for power failure on RPS power input

OFF

Storm control managed by switch configuration

Enable storm control (Broadcast and DLF rate set to 300pps)

Takes precedence over storm control switch configuration

OFF

802.1p QoS managed by switch configuration

Enable 802.1p QoS on ports 1 and 2 (Set CoS priority to tag 4
on ports 1 and 2)

Takes precedence over 802.1p QoS switch configuration

OFF

Port 9 SFP set to Gigabit speed full duplex

Port 9 SFP set to 100Mbps speed full duplex

OFF

Port 10 SFP set to Gigabit speed full duplex

Port 10 SFP set to 100Mbps speed full duplex

Summary of Contents for TI-G160WS




















































































































































Search results

Summary of Contents for TI-G160WS

Reviews:

TRENDnet TI-G160WS, User Manual, Page: 11 / 148

Search results

Summary of Contents for TI-G160WS

Reviews: