TRENDnet TI-G160WS User Manual Download Page 6 | Manualshive

Page: 6 / 148

TRENDnet TI-G160WS User Manual Download Page 6

© Copyright 2019 TRENDnet. All Rights Reserved.

TRENDnet User’s Guide

Industrial Managed Switch Series

3

Products Hardwares and Features

PoE

TI-PG541i

Front View

LED Indicators



Ports 1-4 – Designed to operate at 10Mbps, 100Mbps, or Gigabit speed in both
half-duplex and full-duplex transfer modes. Supports Auto MDI-X and capable
of delivering up to 30W (802.3at PoE+) per port.



Port 5 - Designed to operate at 10Mbps, 100Mbps, or Gigabit speed in both
half-duplex and full-duplex transfer modes. Supports Auto MDI-X



SFP Slot 6 – Designed to operate at Gigabit speeds.



Reset/Reboot Button – Push the button for 10 seconds and release to reset the
switch to factory defaults. Push the button for 3 seconds and release to reboot.



Grounding point/screw – The switch chassis can also be connected to a known
ground point for additional safety and protection. (grounding wire not
included)

Note: For any unused ports or SFP slots, it is recommended to leave the rubber plugs
installed during operation.

LED

State

Status

PWR
(Green)

ON

When the PWR LED is on, the device is using the primary

power input source.

OFF

Primary power input source is off, disconnected, or has

failed.

RPS
(Green)

ON

When the RPS LED lights on, the device is using the

redundant power input source.

OFF

Redundant power input source is off, disconnected or has

failed.

ALM
(Red)

ON

Indicates alarm has been triggered on DIP switch settings and

signal sent out through ALM terminals on terminal block to

third party alarm device.

OFF

No alarm triggered.

POST
(Green)

ON

Device is ready and completed boot process.

OFF

Device is not ready.

SFP Slot 6
(Green)

ON

SFP link is connected.

BLINKING Data is transmitting/receiving.
OFF

SFP link is disconnected.

PoE Ports 1-4
(Green)

ON

PoE supplied to Ethernet port.

OFF

No PoE supplied to Ethernet port.

Ports 1-5
1000M
(Green)

10/100M
(Off)

ON

Ethernet port is connected.

BLINKING Data is transmitting/receiving.

OFF

Ethernet port is not connected.

LED Indicators

PoE+ Gigabit
RJ-45 ports

10/100/1000
Mbps per port
LED indicator

LINK/ACT per
port LED
indicator

IP30 Rated
Housing

PoE LEDs

SFP+ Slots

Gigabit
RJ-45 port

«
...
4
5
6
7
8
...
»

Summary of Contents for TI-G160WS





















































































































































Reviews:

No comments