TRENDnet TI-G160WS User Manual Download Page 45

Page: 45 / 148

TRENDnet User’s Guide

Industrial Managed Switch Series

CLI Configuration

Node

Command

Description

enable

show storm-control

This command displays the current
storm control configurations.

configure

This

command

enables

the

bandwidth limit for broadcast or
multicast or DLF packets and set
the limitation.

configure

This

command

disables

the

bandwidth limit for broadcast or
multicast or DLF packets.

Example:

[DEVICE_NAME]#configure terminal

[DEVICE_NAME](config)#storm-control rate 1 type broadcast ports 1-6

[DEVICE_NAME](config)#storm-control rate 1 type multicast ports 1-6

[DEVICE_NAME](config)#storm-control rate 1 type DLF ports 1-6

Web Configuration

Advanced Settings > Bandwidth Control > Rate Limitation > Storm Control

Parameter Description

Port

Select the port number for which you want to configure storm control
settings.

Rate

Select the number of packets (of the type specified in the Type field) per
second the Switch can receive per second.

Type

Select Broadcast - to specify a limit for the amount of broadcast packets
received per second.

Multicast - to specify a limit for the amount of multicast packets
received per second.

DLF - to specify a limit for the amount of DLF packets received per
second.

Apply

Click Apply to take effect the settings.

Refresh

Click Refresh to begin configuring this screen afresh.

Bandwidth Limitation

Summary of Contents for TI-G160WS




















































































































































Search results

Summary of Contents for TI-G160WS

Reviews:

TRENDnet TI-G160WS, User Manual, Page: 45 / 148

Search results

Summary of Contents for TI-G160WS

Reviews: