manualshive.com logo in svg

Trane CSRA025FAF0, Installation Operation & Maintenance

Share
Download
Trane CSRA025FAF0 Installation Operation & Maintenance Download Page 81

CSRA-SVX02A-EN

81

Service & Maintenance

WARNING

Hazardous Voltage!

Disconnect all electric power, including remote disconnects before 
servicing. Follow proper lockout/tagout procedures to ensure the 
power can not be inadvertently energized. Failure to disconnect power 
before servicing could result in death or serious injury.

[ ] Inspect the expansion valve sensing bulbs for cleanliness. Clean if 
required. Sensing bulbs must make good contact with suction lines and be 
properly insulated.

[ ] Clean condenser fans. Check fan assemblies for proper orifice clearance 
and for motor shaft mis-alignment, abnormal end-play or vibration and noise.

WARNING

Rotating Components!

Disconnect all electric power, including remote disconnects before 

servicing. Follow proper lockout/tagout procedures to ensure the power 

can not be inadvertently energized. Failure to disconnect power before 

servicing could result in death or serious injury. 

Summary of Contents for CSRA025FAF0




















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands