TP-Link Archer C50 User Manual Download Page 20

Page: 20 / 135

Chapter 4

Configure the Router in Wireless Router Mode

4. 3. Operation Mode

The router supports three operation modes: Wireless Router mode, Access Point mode,
and Range Extender Mode.
The default mode is

Wireless Router

mode, which is required most commonly. In this

mode, the device enables multiple users to share the internet connection via ADSL/
Cable Modem.
For hardware connection, refer to

Connect Your Router

4. 4. Network

4. 4. 1. WAN

1. Visit

http://tplinkwifi.net

, and log in with the password you set for the router.

2. Go to

Network

WAN

3. Configure the IP parameters of the LAN and click

Save

Dynamic IP

If your ISP provides the DHCP service, please select

Dynamic IP

, and the router will

automatically get IP parameters from your ISP.
Click

Renew

to renew the IP parameters from your ISP.

Click

Release

to release the IP parameters.

•

MTU Size

- The normal MTU (Maximum Transmission Unit) value for most Ethernet

networks is 1500 Bytes. It is not recommended that you change the default MTU size
unless required by your ISP.

•

Get IP with Unicast

- A few ISPs’ DHCP servers do not support the broadcast

applications. If you cannot get the IP address normally, you can choose this option. (It
is rarely required.)

Summary of Contents for Archer C50








































































































































Search results

Summary of Contents for Archer C50

Reviews:

Related manuals for Archer C50

Brands by name

Popular brands

TP-Link Archer C50, User Manual

Search results

Summary of Contents for Archer C50

Reviews:

Related manuals for Archer C50

Brands by name

Popular brands