manualshive.com logo in svg

Toyota LAND CRUISER, Owner'S Manual

Share
Download
Toyota LAND CRUISER Owner'S Manual Download Page 243

242

2-4. Using other driving systems

L/C200_OM_OM60K60E_(AE)

■

Cruise control can be set when

●

The shift lever is in the “D” or range “4” or higher of “S” has been
selected.

●

Vehicle speed is above approximately 40 km/h (25 mph).

■

Accelerating after setting the vehicle speed

●

The vehicle can be accelerated normally. After acceleration, the set
speed resumes.

●

Even without canceling the cruise control, the set speed can be
increased by first accelerating the vehicle to the desired speed and then
pushing the lever down to set the new speed. 

■

Automatic cruise control cancelation

Cruise control will stop maintaining the vehicle speed in any of the following
situations. 

●

Actual vehicle speed falls more than approximately 16 km/h (10 mph)
below the preset vehicle speed.
At this time, the memorized set speed is not retained.

●

VSC is activated.

●

Actual vehicle speed is below approximately 40 km/h (25 mph).

●

The switching operation continues for 5 seconds or more after the center
differential lock switch has been operated.

■

If the warning message for the cruise control is shown on the multi-
information display or the cruise control indicator light turns to yellow

Press the “ON-OFF” button once to deactivate the system, and then press
the button again to reactivate the system.
If the cruise control speed cannot be set or if the cruise control cancels
immediately after being activated, there may be a malfunction in the cruise
control system. Have the vehicle inspected by your Toyota dealer.

Not 

for 

Reproduction

Summary of Contents for LAND CRUISER















































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands