manualshive.com logo in svg

Toshiba Satellite P20-25 Series, Maintenance Manual

Share
Download
Toshiba Satellite P20-25 Series Maintenance Manual Download Page 68

2.12  Optical Drive Troubleshooting 

2  Troubleshooting Procedures 

Procedure 5 

Connection check and replacement check 

The optical drive connects to the system board. The drive may be disconnected, or the drive or 
system board may be damaged. Disassemble the computer following the steps described in 
Chapter 4, 

Replacement Procedures

, and perform the following checks: 

 
Check 1 

Make sure the drive is firmly connected to the system board. If the connection is 
good and there is still an error, go to Check 2. 

Check 2 

The drive or drive cable may be defective or damaged. Replace each with a new one 
following the steps in Chapter 4, 

Replacement Procedures

. If the drive is still not 

functioning properly, perform Check 3. 

Check 3 

The system board may be damaged. Replace it with new one following the 
instructions in Chapter 4, Replacement Procedures.  

Satellite P20-25 Series Maintenance Manual 

 

2-31 

Summary of Contents for Satellite P20-25 Series



























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands