manualshive.com logo in svg

Toshiba Satellite P20-25 Series, Maintenance Manual

Share
Download
Toshiba Satellite P20-25 Series Maintenance Manual Download Page 16

1  Hardware Overview 

1.1 Features

 

 

HDD 

• 

One 2.5", 9.5mm hard disk with capacity 30GB/40GB/60GB/80GB 

• 

Bus Master IDE 

• 

9.5mm, 2.5”HDD support 

• 

Support Ultra 100 synchronous DMA 

 

FDD / DVD Devices 
One of the following: 

• 

12.7mm, 1.44MB FDD device  

• 

5.25” 12.7mm height DVD-R/RW device 

• 

5.25” 12.7mm height DVD-ROM device 

• 

5.25” 12.7mm height DVD multi-drivedevice 

• 

5.25” 12.7mm height combo device 

 

Keyboard 

An easy-to-use 87-key keyboard provides a numeric keypad overlay for fast numeric 
data entry or for cursor and page control. It supports software that uses a 101- or 102-
key enhanced keyboard. Includes one Windows

®

 key and one Application key. 

 

TouchPad 

This pointing control device, located in the center of the keyboard palm-rest, provides 
convenient control of the cursor without requiring desk space for a mouse. The 
TouchPad incorporates two mouse buttons. 

 

Display 

The following types of display are available: 

• 

17.0-inch WXGA TFT screen, 1440

×

900 pixels, Response time 31ms (typ.); 

Contrast ratio 350:1 (typ.); Brightness 150 Nit (typ.) 

• 

17.1-inch WXGA TFT screen, 1440

×

900 pixels, Response time 31ms (typ.); 

Contrast ratio 300:1 (typ.); Brightness 160 Nit (typ.) 

 

Optional devices 

• 

64MB/128MB/256MB/512MB SO-DIMM modules 

• 

MINI PCI module(802.11b wireless LAN module) 

• 

Modem with MDC solution module 

 

1-2 

Satellite P20-25 Series Maintenance Manual 

Summary of Contents for Satellite P20-25 Series



























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands