manualshive.com logo in svg

Toshiba Satellite P20-25 Series, Maintenance Manual

Share
Download
Toshiba Satellite P20-25 Series Maintenance Manual Download Page 173

4.19  Display Assembly 

4  Replacement Procedures 

Installing the Display Assembly 

To install the display assembly, follow the steps below and refer to the figures in the 
preceding section. 

1.  Seat the display assembly taking care not to crush to the 

LCD display cable 

or 

wireless LAN antenna

. 

2. Feed the 

wireless LAN antenna

 through the system board into the 

wireless LAN 

compartment

.  

3. If a 

wireless LAN card

 is installed, remove the 

wireless LAN compartment cover 

and attach the ends of the 

wireless LAN antenna

 to the card. The 

black antenna 

cable

 should be attached to the connector nearer the rear side of the computer, the 

white antenna cable 

to the connector closer to the front panel. 

4.  Secure the hinges with 

two M2.5

×

6 screws

. Use the same screw to secure

 

the 

display cable 

to the left side hinge. 

5. Attach the 

display cable

 to its connector on the

 system board

.  

6. Seat the 

hinge cover

 and secure its top-side with 

one m2.5

×

12 screw 

at the left end 

and 

one m2.5

×

3 silver screw 

at the right end. 

7. Secure the 

hinge cover

 with 

one M2

×

4 screw

 at the rear of the each hinge. 

8.  Secure the display assembly with two 

M2.5

×

6 screws

 on the 

I/O cover

. 

 

Satellite P20-25 Series Maintenance Manual  

4-57 

Summary of Contents for Satellite P20-25 Series



























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands