manualshive.com logo in svg

Toshiba Satellite P20-25 Series, Maintenance Manual

Share
Download
Toshiba Satellite P20-25 Series Maintenance Manual Download Page 61

2  Troubleshooting Procedures  

2.9  Printer Port Troubleshooting

 

To determine if the computer’s printer (parallel) port is functioning properly, perform the 
following procedures. Figure 2-8 outlines the process. Start with Procedure 1 and continue as 
instructed. 

Procedure 1:  Diagnostic check 
Procedure 2:  Printer port loopback check 
Procedure 3:  Replace system board 

Procedure 1 

Diagnostic check 

Attach the printer port loopback connector firmly to the printer port and run the Diagnostic 
Program. See Chapter 3 for details. If the printer port test passes, there may be a problem with 
the printer. Go to Procedure 2. If the printer port test fails, go to Procedure 3. 

Procedure 2 

Printer port loopback check 

The printer may be faulty or not connected properly. Perform Check 1. 

Check 1 

Make sure printer cable is firmly plugged into both the printer and the printer port of 
the computer. If the cable is connected correctly, go to Check 2. 

Check 2 

Make sure the printer port is firmly secured to the system board of the computer. If 
the malfunction remains, go to Check 3. 

Check 3 

The printer cable may be damaged. Replace with a good cable. If the malfunction 
remains, go to Check 4.  

Check 4 

The printer may be faulty. Replace it with a good printer or connect it to a different 
computer. 

If the replacement printer works or the original printer does not work on a different 
computer, the printer should be replaced. 

If the replacement printer does not work either, or the original printer functions 
normally on a different computer, go to Procedure 3. 

Procedure 3 

Replace system board 

The system board may be damaged. Replace it with a new one following the instructions in 
Chapter 4. 

 

2-24 

Satellite P20-25 Series Maintenance Manual 

Summary of Contents for Satellite P20-25 Series



























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands