manualshive.com logo in svg

Toshiba Satellite P20-25 Series, Maintenance Manual

Share
Download
Toshiba Satellite P20-25 Series Maintenance Manual Download Page 177

4.20  System Board 

4  Replacement Procedures 

Installing the System Board 

To install the system board, follow the steps below and refer to the figures in the preceding 
section. 

1. Seat the 

system board

 and secure with 

three M2.5

×

6 screws

. 

2.  Secure the following 

five cables 

to the system board: 

•

 

Right-side speaker cable 

•

 

Direct play LED FPC cable 

•

 

CIR FFC cable 

•

 

Direct play button FFC  

•

 

Audio board FFC cable 

3. Position the 

low I/O cover

. 

4.  Secure the parallel port and external monitor port with 

two hexagonal port screws 

each.  

5. Secure the 

low I/O cover

 with 

nine M2.5

×

4 screws

 (five to the top, two to the rear, 

and two to the base). 

6.  Replace the other removed FRUs - 

keyboard

, 

HDD

, 

main

 

module, CPU, modem or 

Bluetooth unit

,

 expansion memory cards

, 

wireless LAN cards

,

 PC card(s)

 and 

top cover

- remembering to reattach the three fan cables. 

 

Satellite P20 Series Maintenance Manual 

4-61 

Summary of Contents for Satellite P20-25 Series



























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands