Toshiba Satellite P20-25 Series Maintenance Manual Download Page 198

Page: 198 / 250

4 Replacement Procedures

4.29 LCD Module

4-82

Satellite P20-25 Series Maintenance Manual

Installing the LCD Module

To install the LCD module, follow the steps below and refer to the figures in the
preceding section.

1. Connect the

LCD cable

to the

LCD connector

on the back of the

LCD module

2. Secure the

LCD cable

with

Kapton film

3. Secure the

LCD bracket

to the

LCD module

with

eight M2

3 screws

(the number

of bracket screws may vary on different models).

4. Position the

LCD module

in place.

5. Secure the

LCD module

with

six M2.5

6 screws

. First secure the screws (one on

each side) nearer the base of the module, then secure the screws nearer the top.

6. Secure

LCD cable

with

one

M2.5

4 screw

Summary of Contents for Satellite P20-25 Series



























































































































































































































































Search results

Summary of Contents for Satellite P20-25 Series

Reviews:

Brands by name

Popular brands

Toshiba Satellite P20-25 Series, Maintenance Manual

Search results

Summary of Contents for Satellite P20-25 Series

Reviews:

Brands by name

Popular brands