Toshiba E-STUDIO5506AC Imaging Manual Download Page 6

Page: 6 / 331

ALLGEMEINE SICHERHEITSMASSNAHMEN IN BEZUG AUF DIE

WARTUNG

Die Installation und die Wartung sind von einem qualifizierten Service-

Techniker durchzuführen.

1. Transport/Installation

- Zum Transportieren/Installieren des Gerätes werden 2 Personen benötigt. Bewegen Sie es mit den

Rollen, während Sie die Absperrvorrichtungen heben. Das Gerät ist sehr schwer und wiegt etwa 213 kg;

deshalb muss bei der Handhabung des Geräts besonders aufgepasst

werden

- Beim Transportieren des Geräts nicht an den beweglichen Teilen oder Einheiten (z.B. das

Bedienungsfeld, die Duplexeinheit oder die automatische Dokumentenzuführung) halten.

- Eine spezielle Steckdose mit Stromversorgung von AC 120V/20A, 220-240V/10A als Stromquelle

verwenden.

- Das Gerät ist aus Sicherheitsgründen zu erden.

- Einen geeigneten Standort für die Installation wählen. Standorte mit zuviel Hitze, hoher

Luftfeuchtigkeit, Staub, Vibration und direkter Sonneneinstrahlung sind zu vermeiden.

- Für ausreichende Belüftung sorgen, da das Gerät etwas Ozon abgibt.

- Um einen optimalen Kopierbetrieb zu gewährleisten, muss ein Abstand von mindestens 80 cm links,

80 cm rechts und 10 cm dahinter eingehalten werden.

- Das Gerät ist in der Nähe der Steckdose zu installieren; diese muss leicht zu erreichen sein.

- Nach der Installation muss das Netzkabel richtig hineingesteckt und befestigt werden, damit niemand

darüber stolpern kann.

- Falls der Auspackungsstandort und der Installationsstandort des Geräts verschieden sind, die

Bildqualitätsjustierung (automatische Gammajustierung) je nach der Temperatur und Luftfeuchtigkeit

des Installationsstandorts und der Papiersorte, die verwendet wird, durchführen.

- Wenn das Gerät nach der Entfernung der Extras verwendet wird, die entfernten Teile oder

Abdeckungen anbringen, damit das Innere des Gerät nicht freiliegt.

- Wenn LAN-Kabel, USB-Kabel oder die Telefonleitung angeschlossen sind, müssen diese Kabel

durch die Klemme an der Rückwand verlegt werden.

Ansonsten können sie beim Öffnen/Schließen der Duplexeinheit eingeklemmt und beschädigt

werden.

2. Allgemeine Sicherheitsmassnahmen in bezug auf die Wartung

- Während der Wartung das Gerät ausschalten und das Netzkabel herausziehen (ausser Wartung, die

bei einem eingeschalteten Gerät, durchgeführt werden muss).

- Das Netzkabel herausziehen und den Bereich um die Steckerpole und die Steckdose die Umgebung

in der Nähe von den Steckerzacken und der Steckdose wenigstens einmal im Jahr reinigen. Wenn

Staub sich in dieser Gegend ansammelt, kann dies ein Feuer verursachen.

- Wenn die Teile auseinandergenommen werden, wenn nicht anders in diesem Handbuch usw erklärt,

ist das Zusammenbauen in umgekehrter Reihenfolge durchzuführen. Aufpassen, dass kleine Teile

wie Schrauben, Dichtungsringe, Bolzen, E-Ringe, Stern-Dichtungsringe, Kabelbäume nicht an den

verkehrten Stellen eingebaut werden.

- Grundsätzlich darf das Gerät mit enfernten oder auseinandergenommenen Teilen nicht in Betrieb

genommen werden.

Summary of Contents for E-STUDIO5506AC









































































































































































































































































































































Search results

Summary of Contents for E-STUDIO5506AC

Reviews:

Toshiba E-STUDIO5506AC, Imaging Manual, Page: 6 / 331

Search results

Summary of Contents for E-STUDIO5506AC

Reviews: