Toshiba E-STUDIO5506AC Imaging Manual Download Page 109

Page: 109 / 331

e-STUDIO5506AC/6506AC/7506AC (Ver01)

2-63

2. Copier-specific Adjustments

* Set the value in increments of approximately 10, while checking the copy image until the optimum value is

obtained.

* The value for the code corresponding to the original mode (Text/Photo, Text, or Printed image) will affect

the copy image quality in the Full color mode and the Auto color mode.

* The subcode varies according to the area where the density is adjusted. Refer to the table below and set the

subcode for the area to be adjusted.

Subcode

Area where the density is adjusted

Low-density area

Medium-density area

High-density area



Caution after the adjustment

Nothing in particular.



Remarks

• Enter a value within the recommended value range mentioned in the procedures. Otherwise, it may cause a loss

in MFP performance, including degradation in the image quality and a reduction in the life of the consumables

• If the adjustment causes a toner fixing problem, decrease the values for codes 05-7905 to 7911.

Summary of Contents for E-STUDIO5506AC









































































































































































































































































































































Search results

Summary of Contents for E-STUDIO5506AC

Reviews:

Toshiba E-STUDIO5506AC, Imaging Manual, Page: 109 / 331

Search results

Summary of Contents for E-STUDIO5506AC

Reviews: