Home
/
Toshiba
/
E-STUDIO5506AC
/
Imaging Manual

Toshiba E-STUDIO5506AC, Imaging Manual, Page: 107 / 331

Share

Page: 107 / 331

Toshiba E-STUDIO5506AC Imaging Manual Download Page 107

e-STUDIO5506AC/6506AC/7506AC (Ver01)

© 2016, 2017 TOSHIBA TEC CORPORATION All rights reserved

2-61

2. Copier-specific Adjustments

(1) Perform automatic calibration for each paper type to correct variations in image density.

* A privilege to perform automatic calibration is set to Administrator by default but this can be changed to

the User. For how to change the privilege, refer to the MFP Management Guide.

• Follow steps (a) through (j) to perform the automatic calibration.

(a) Select [08 SETTING MODE]. Change the value of the code [9059] to “1” so that automatic

calibration for each paper type will be enabled.

Value for 08-9059

Display for user calibration

0

Not displayed (default)

1

Displayed

(b) Press [USER FUNCTIONS] on the Control Panel to enter the “User Functions” menu.

(c) Press [ADMIN].

(d)  Enter an administrator password in 6 to 64 digits. Press [ENTER].
(e)  Press [GENERAL].
(f)  Press [CALIBRATION].
(g)  Press [COPY].
(h) Select the paper type for correction.
(i)  Press [CALIBRATION] to print a test chart.
(j)  Place the printed test chart on the original glass.
(k)  Press the [START] button to start the calibration. The message “WAIT” disappears when the

calibration is finished.

* The procedure above covers both the color and black copy calibration.

After the automatic calibration, copy and check the image quality.

If further image quality adjustment is necessary, go to the next step.

(2) Select [05 ADJUSTMENT MODE]. Change the values for codes [7913] to adjust the amount of toner used.

• The code to use varies according to the paper type. Adjust the value for [05] code corresponding to the

paper type for whose image quality you would like to improve and increase the value to obtain the copy
density that the user desires.

• In the [7913] setting, the toner amount of Y, M, C and K single colors is not changed, but that of the

overlaid colors reproduced by two or more colors, such as R, G, B and K, is controlled.

Paper type

[05] code Subcode Recommended

value

Acceptable

value range

Default

Thick 1

05-7913

3

128

0 to 255

128

Thick 2

4

Thick 3

5

Thick 4

6

Special 1

7

Special 2

8

Special 3

9

OHP

12

* Set the value in increments of approximately 4, while checking the copy image until the optimum value is

obtained.

* Although the larger the value, the darker the density becomes, offsetting may occur if the value is too large.

Adjust the value while checking the copy image carefully.

«
...
105
106
107
108
109
...
»

Summary of Contents for E-STUDIO5506AC












































































































































































































































































































































Reviews:

No comments