Toro TimeCutter HD MyRide 60in Operator'S Manual Download Page 6

Page: 6 / 32

Procedure

Description

Qty.

Use

Weight-mount bracket

Carriage bolt (5/16 x 3/4 inch)

Flange nut (5/16 inch)

Front weight

Bolt (3/8 x 1 inch)

Lock washer

Flat washer

Flange nut (3/8 inch)

Install the weights.

No parts required

–

Check the tire pressure.

Note:

Determine the left and right sides of the machine from the normal operating position.

Preparing the Mower

No Parts Required

Procedure

Perform the following procedure to prepare the mower for
attaching the blower and bagger kit.

Disengage the PTO, move the motion-control levers
to the N

EUTRAL

locked position, and set the parking

brake.

Shut off the engine, remove the key, and wait for all
moving parts to stop before leaving the operating
position.

Repair all bent or damaged areas of the mower deck
and replace any missing parts.

Clean the mower of any debris on the deck or rear part
of the mower to ease installation.

Installing the Side Bumpers
and Support Brackets

Parts needed for this procedure:

Left bumper

Left frame-support bracket

Right bumper

Right frame-support bracket

Carriage bolt (3/8 x 1-1/4 inches)

Flange nut (3/8 inch)

Procedure

Remove the left and right bumpers as follows:

Remove the nuts and bolts securing the left side
bumper and muffler shield to the chassis and
center engine guard as shown in

Figure 4

Summary of Contents for TimeCutter HD MyRide 60in

































Search results

Summary of Contents for TimeCutter HD MyRide 60in

Reviews:

Related manuals for TimeCutter HD MyRide 60in

Brands by name

Popular brands

Toro TimeCutter HD MyRide 60in, Operator'S Manual

Search results

Summary of Contents for TimeCutter HD MyRide 60in

Reviews:

Related manuals for TimeCutter HD MyRide 60in

Brands by name

Popular brands