Toro TimeCutter HD MyRide 60in Operator'S Manual Download Page 19

Page: 19 / 32

g018371

Figure 25

Installing the Tension Spring and Aligning the Belt

Blower assembly

Spring

Latch pin (locking position)

Idler spring post

Chute bracket

Spring hook end

Idler pivot bracket

Belt (aligned to the idler
pulley)

Fixed spring post

Note:

Ensure that the latch firmly holds the blower

assembly against the mower deck, but can be released
by hand.

Route the belt around the drive pulley as illustrated in

Figure 20

and

Figure 21

Temporarily route the belt beneath the idler pulley
(

Figure 25

Move the idler pivot bracket toward the fixed spring
post. Install the spring by aligning the spring hook on
to the idler spring post (

Figure 25

Note:

Ensure that the spring hooks are correctly

positioned on the spring posts.

10.

Pull the spring loaded idler pulley away from the fixed
spring post, and route the belt around the mower deck
pulley (

Figure 25

Note:

Ensure the belt is routed around the blower

pulley correctly.

Installing the Belt Cover

Parts needed for this procedure:

Belt cover (from the blower and drive kit)

Cover knob

Procedure

Lower the mower deck to the lowest height-of-cut
position.

Align the new right-hand belt cover with the belt-cover
bracket and the notches in the deck bracket.

Install the new belt cover so that the notches on both
sides of the cover go over the belt-cover supports and
secure the latch (

Figure 26

G018445

Figure 26

Installing the Belt Cover

Belt cover

Cover knob

Belt-cover support

Notch

Secure the new belt cover to the deck by installing the
cover knob from the blower and drive kit through the
cover and threaded into the belt cover support (

Figure

Summary of Contents for TimeCutter HD MyRide 60in

































Search results

Summary of Contents for TimeCutter HD MyRide 60in

Reviews:

Related manuals for TimeCutter HD MyRide 60in

Brands by name

Popular brands

Toro TimeCutter HD MyRide 60in, Operator'S Manual

Search results

Summary of Contents for TimeCutter HD MyRide 60in

Reviews:

Related manuals for TimeCutter HD MyRide 60in

Brands by name

Popular brands