Toro TimeCutter HD MyRide 60in Operator'S Manual Download Page 10

Page: 10 / 32

Align the right flange of the exhaust
shield (the flange with 2 holes) to the
rear surface of the lower-left engine
guard (

Figure 7

G018637

Figure 7

Heat Shield Installation on US Domestic Mower

ii.

Align the bottom edge of the
exhaust-shield right flange to the
bottom edge of the engine guard
(

Figure 7

iii.

Align the left flange of the exhaust
shield (the flange with 1 hole) to the
surface of the small, angular area of
the lower-left engine guard. (

Figure 7

Note:

Ensure the left flange (the

flange with 1 hole) of the exhaust
shield is flush with the engine-guard
surface.

iv.

Align the top edge of the
exhaust-shield left flange and
the top edge of the lower-left engine
guard so that the flange edge and the
guard edge are parallel (

Figure 7

Mark the outline of all holes in the
exhaust-shield flanges on to the
lower-left engine guard, and remove
the exhaust shield from the engine
guard.

•

For International (TE) Mowers

Align the holes of the exhaust-shield
right flange (the flange with 2 holes)

to the two left-most-vertical slots in
the lower-left engine guard (

Figure 8

G018638

Figure 8

Heat Shield Installation on International (TE) Mower

Flange-hex-head bolt (3/8 x 1 inch) and Nut (3/8 inch)

ii.

Align the bottom edge of the right
flange of the of the exhaust shield to
the bottom edge of the engine guard
(

Figure 8

iii.

Loosely secure the right flange of the
exhaust shield to the engine guard
with 2 flange-hex-head bolts (3/8 x 1
inch) and 2 flange nuts (3/8 inch).

iv.

Align the left flange of the exhaust
shield (the flange with 1 hole) to
angular area of the lower-left engine
guard (

Figure 8

Note:

Ensure that the left flange

(the flange with 1 hole) of the exhaust
shield is flush with the engine-guard
surface.

Mark the outline of the hole in the left
flange of the exhaust shield on to the
lower-left engine guard.

vi.

Remove the fasteners and exhaust
shield from the engine guard.

Locate the center of the marks on the lower-left
engine-guard surface, and center-punch the locations.

Drill a 10 mm (3/8 inch) hole in the engine guard at
the center-punch mark created in step

Summary of Contents for TimeCutter HD MyRide 60in

































Search results

Summary of Contents for TimeCutter HD MyRide 60in

Reviews:

Related manuals for TimeCutter HD MyRide 60in

Brands by name

Popular brands

Toro TimeCutter HD MyRide 60in, Operator'S Manual

Search results

Summary of Contents for TimeCutter HD MyRide 60in

Reviews:

Related manuals for TimeCutter HD MyRide 60in

Brands by name

Popular brands