Toro TimeCutter HD MyRide 60in Operator'S Manual Download Page 5

Page: 5 / 32

Setup

Loose Parts

Use the chart below to verify that all parts have been shipped.

Procedure

Description

Qty.

Use

No parts required

–

Prepare the mower.

Left bumper

Left frame-support bracket

Right bumper

Right frame-support bracket

Carriage bolt (3/8 x 1-1/4 inches)

Flange nut (3/8 inch)

Install the side bumpers and support
brackets.

Tailpipe extension

Washer-head screw (#8 x 1/2 inch,
self-threading)

Install the muffler extension.

Exhaust shield

Flange-hex-head bolt (3/8 x 1 inch)

Nut (3/8 inch)

Drill the exhaust-shield mounting holes.

Exhaust shield

Flange-hex-head bolt (3/8 x 1 inch)

Nut (3/8 inch)

Install the exhaust heat shield.

Hopper-support frame

Hairpin

Hood hold-down rod

Install the bagger mounting brackets.

Bagger hood

Baffle

Hairpin (small)

Install the hood baffle.

Hood assembly

Bag

Install the hood assembly and bags.

Blower (from the blower and drive kit)

Blower belt (from the blower and drive
kit)

Route the blower belt into the blower
assembly.

Blower assembly (from the blower and
drive kit)

Spring (from the blower and drive kit)

Install the blower assembly.

Belt cover (from the blower and drive kit)

Cover knob

Install the belt cover.

Upper discharge tube

Screw (1/4 x 3/4 inch)

Locknut (1/4 inch)

Lower discharge tube

Install the discharge tubes.

Summary of Contents for TimeCutter HD MyRide 60in

































Search results

Summary of Contents for TimeCutter HD MyRide 60in

Reviews:

Related manuals for TimeCutter HD MyRide 60in

Brands by name

Popular brands

Toro TimeCutter HD MyRide 60in, Operator'S Manual

Search results

Summary of Contents for TimeCutter HD MyRide 60in

Reviews:

Related manuals for TimeCutter HD MyRide 60in

Brands by name

Popular brands