Topcon System 350 Operator'S Manual Download Page 13 | Manualshive

Page: 13 / 112

background image

X30 Spreader Controller

0-10

Exposure to Radio Frequency

Exposure to energy from radio frequencies is an important safety
issue. Keep a distance of at least 20 cm (7.8 inches) between
people and any radiating antenna. Keep a distance of at least 20
cm between transmitting antennas.

Warning: Products using cellular modem or an
RTK base station can transmit radio frequency
energy. Check with your dealer.

This device is designed to operate with TPA approved antennas.
Discuss with your dealer.

Preparation for Operation



Read and understand this manual and learn all of the controls
before you use the equipment.



Keep the manual with the equipment.



If the equipment is moved to another vehicle, move the
manual as well.



Read the manual for the vehicle with which the equipment
will be used and check that the vehicle has the correct
equipment required by local regulations.



Make sure you understand the speed, brakes, steering,
stability, and load characteristics of the vehicle before you
start.



Check all controls in an area clear of people and obstacles
before starting work.



Identify possible hazards.

Warning: Topcon equipment must not be used by an
operator affected by alcohol or drugs. Seek medical
advice if using prescription or over-the-counter

«
...
11
12
13
14
15
...
»

Summary of Contents for System 350

















































































































Reviews:

No comments

Related manuals for System 350

Brand: ABB Pages: 52

Brand: 7bit Pages: 2

Brand: Jafar Pages: 15

Brand: FAAC Pages: 60

Brand: FAAC Pages: 12

Brand: FAAC Pages: 44

Brand: FAAC Pages: 44

Brand: FAAC Pages: 8

Brand: FAAC Pages: 60

Brand: FAAC Pages: 14

Brand: FAAC Pages: 68

Brand: FAAC Pages: 16

Brand: Garmin Pages: 220

Brand: Gardena Pages: 16

Brand: VAT Pages: 27

MorphoAccess SIGMA Extreme Series

Brand: Idemia Pages: 31

Brand: ICP DAS USA Pages: 148

Brand: ICMA Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands