Topcon System 350 Operator'S Manual Download Page 92

Page: 92 / 112

Chapter 4 - Operations

4.10 Using the Master Switch

X30 Spreader Controller

4-22

4.10 Using the Master Switch

When Virtual Master has been chosen in the setup options,
the

Spreader Master Switch

turns the spreader system on

from the X30 Console.

This switch does not work if External ECU Sense was chosen
during setup.

The Master Switch button appears in green, white or red to
indicate the readiness of the system:

Green: Spreader Controller is on and working. Select
the master switch to turn the spreader off.

White: Spreader Controller is ready to use. Select the
master switch to turn the spreader on.

Red: Spreader Controller is off and cannot be used.
Select the Master Switch to see possible causes of the
problem. See the example below.

Green indicates that the system is ready.
Red indicates that the system is not
ready.

Select

to return to the main screen

and complete the necessary action.

Summary of Contents for System 350

















































































































Search results

Summary of Contents for System 350

Reviews:

Related manuals for System 350

Brands by name

Popular brands

Topcon System 350, Operator'S Manual

Search results

Summary of Contents for System 350

Reviews:

Related manuals for System 350

Brands by name

Popular brands