Topcon System 350 Operator'S Manual Download Page 106

Page: 106 / 112

Chapter 5 - Variable Rate Control

5.3 Downloading VRC Map Files with AgJunction

X30 Spreader Controller

5-10

5.3 Downloading VRC Map Files with AgJunction

If AgJunction creates the VRC map files, the X30 console
can now download files from the website using a Link ID and
login. To use this feature ensure the console is connected to
the internet.

This feature needs to be enabled. Select

to return to the

Main Setup Screen

from the

Operations Screen

1. Select System on the

Main Setup Menu

, Features and

AgJunction.

Escape to Operations Screen

2. Choose Enabled and Confirm. The AgJunction icon will

now appear on the operations

Navigation Bar

3. Select Escape to return to the

Operations Screen.

Summary of Contents for System 350

















































































































Search results

Summary of Contents for System 350

Reviews:

Related manuals for System 350

Brands by name

Popular brands

Topcon System 350, Operator'S Manual

Search results

Summary of Contents for System 350

Reviews:

Related manuals for System 350

Brands by name

Popular brands