Toku TNB-08M Manual Download

Page: 109 / 133

105

● TROUBLE SHOOTING GUIDE

5-1.

OIL LEAKAGE

⚫

By referring to the following chart, when oil leakage occurs, investigate the cause and

repair accordingly. After fitting the hydraulic breaker on the excavator, sometimes you

may see oil ooze from the breaker. This is grease, which is used in assembly and may

continue for up to 5 hours, but will stop eventually. But please note, oil coming from

section A (See diagram) between the chisel and chisel bushing, this oil is for lubrication

purposes and is normal.

Oil Leakage Location

Cause

Countermeasure

Opening between the chisel
and the chisel bushing

Wear or damage of oil seal.

(*) Replacement

Seizure of piston & cylinder.

(*) Repair or replacement

Between the cylinder cover
and cylinder.

Wear or damage of O-ring or
back up ring.

(*) Replacement

Looseness of the side bolt
nut.

Retighten the side bolt nut
with the specified torque.

Between the cylinder and the
chalk plug

Wear or damage of O-ring

(*) Replacement.

Looseness of the chalk
plug

Retightening the chalk plug
with the specified torque.

Between the cylinder and the
hose adapter

Wear or damage of O-ring

(*) Replacement.

Looseness of the hose
adapter

Retightening

the

hose

adapter with the specified
torque.

NOTE: (*) It is necessary to disassemble the hydraulic breaker in order to repair.

Please contact TOKU or TOKU

’

s Distributor and ask for repair.

TNB-08M, 1M, 2M, 3MB, 4M, 5M

Summary of Contents for TNB-08M





































































































































Search results

Summary of Contents for TNB-08M

Reviews:

Related manuals for TNB-08M

Brands by name

Popular brands

Toku TNB-08M, Manual

Search results

Summary of Contents for TNB-08M

Reviews:

Related manuals for TNB-08M

Brands by name

Popular brands