Toku TNB-08M Manual Download

Page: 8 / 133

⚫

When operating a hydraulic breaker, install a front guard on the windscreen.

Also place

a laminate coating sheet over the windscreen.

⚫

For work in mines, tunnel or other places where there is a danger of falling rocks, fit a

FOPS (falling object protective structure). Also place a laminate coating sheet over the

windscreen.

⚫

When operating a breaker, make sure that you close the front window.

⚫

During operation, make sure all personnel are out of range of materials, which may fly

up.

The hydraulic breaker contains a high volume of pressurized nitrogen gas. It can

therefore be dangerous if the breaker is not dismantled correctly. As a result, if the

breaker needs service, please contact TOKU or an authorized distributor/ service depot.

⚫

Non-approved modifications can cause injury and damage.

⚫

Consult your TOKU dealer for advice before making any modifications. TOKU will

not accept responsibility for any injury or damage caused by any unauthorized

modifications.

WARNING

-PROTECTION AGAINST FALLING OR FLYING OBJECTS-

WARNING

DON

’

T DISASSEMBLE

WARNING

UNAUTHORIZED MODIFICATION

Top guard

Front guard

Laminate coating sheet

FOPS

FOPS ・・・Falling objects protection structure

Summary of Contents for TNB-08M





































































































































Search results

Summary of Contents for TNB-08M

Reviews:

Related manuals for TNB-08M

Brands by name

Popular brands

Toku TNB-08M, Manual

Search results

Summary of Contents for TNB-08M

Reviews:

Related manuals for TNB-08M

Brands by name

Popular brands