19
E
N
G
L
I
S
H
18
E
N
G
L
I
S
H
Reassembling Receiver Halves:
STEP 1:
❏
Double check that the Trigger Assembly
; and other parts: Feed Elbow Lock
+ Pin
+ Spring
;
Ball Latch
; Front Bolt
*
; Linkage Arm
*
; Link Arm Pins (2)
; Rear Bolt*
+ Bolt Insert
; Bolt Handle
; Drive Spring
*
+
Guide Pin
*
; Buffer O-ring
; End Cap + End Cap Cover ; 2
Tank Adapter Nuts
; are in place and (
*
=oiled) (see below and
schematics on pages 11–12 for details as needed).
❏
❏
❏
❏
❏
Non-E-Trigger
TM
Markers go to STEP 2) on page 19
.
For E-Trigger
TM
Markers:
Do not operate sear tripper assembly uninstalled as solenoid /
armature may pinch you.
E-Trigger
TM
Parts Not Shown
in Basic Parts List on
(pages 12-13)
TA06020 Armature Pin
TA09935
Electronics
Assembly
TA05014 Magnet
Solenoid
-Armature
02-88
Sear Spring
TA01135 Sear
STEP 2:
❏
Carefully install the left receiver half (make sure halves fit flush).
❏
Insert 4 short receiver bolts
.
❏
If marker has a barrel shroud - insert it now.
❏
Insert 3 long receiver bolts
and
❏
Tighten the 7 bolts /
.
❏
Attach adapter
tighten
2 bolts
(NOTE: short adapter
bolt goes in front).
❏
Apply marker oil onto the barrel o-ring, insert
the barrel
and carefully screw it in.
❏
Slide the feed elbow into the receiver and tilt up until the feed lock
holds it in place.
❏
E-Trigger
TM
Markers - Attach a 9 volt battery to the
battery connector and be sure the wires lay flat inside
the cutout area of the receiver.
❏
Carefully tilt and insert the battery (wire attached
end first
) into the receiver.
❏
Install the left receiver grip
with 2 bolts
.
❏
Press in the 2 magazine tabs
and slide the
magazine
up into the marker until the tabs
lock it in place.
NOTE: The magazine may be used
to store tools and lubricating oil for your marker
(shown with 2 allen wrenches
and oil).
Reassembling Receiver Halves:
(continued on page 19)
❏
Double check that the E-Trigger
TM
Parts
are Positioned correctly for Reassembly
as follows:
❏
1)
Place solenoid / (armature - fits
inside solenoid) into right receiver.
❏
2)
Carefully align and insert the
electronics board
into slot.
❏
3)
Place trigger switch on two pins
of right receiver half.
❏
4)
Insert capacitor in slot.
❏
5)
Route wires in cutout areas to lay flat under armature pin and
battery and not be pinched when receiver halves are reassembled.
❏
Visually inspect internal wires for disconnected wire end(s) or
damage.
❏
6)
Insert armature pin into 2 slots so it moves freely.
❏
7)
Insert Magnet
in slot below armature as shown.
❏
Double check that all parts are in place as shown.
❏
Place battery connector
through left receiver half
❏
make
sure the magnet fits into left receiver half slot so it does not break
and
❏
wires are not pinched as you
❏
place left half on right half so
the halves fit flush.
(E-Trigger
TM
Markers Go to STEP 2 on page 19).
Marker Disassembly / Assembly
(continued from page 17)
Carefully hand start
all threaded parts and
do not overtighten and strip threaded parts when assembling.
Reassembling Receiver Halves:
(continued from page 18)
19
E
N
G
L
I
S
H
18
E
N
G
L
I
S
H
Reassembling Receiver Halves:
STEP 1:
❏
Double check that the Trigger Assembly
; and other parts: Feed Elbow Lock
+ Pin
+ Spring
;
Ball Latch
; Front Bolt
*
; Linkage Arm
*
; Link Arm Pins (2)
; Rear Bolt*
+ Bolt Insert
; Bolt Handle
; Drive Spring
*
+
Guide Pin
*
; Buffer O-ring
; End Cap + End Cap Cover ; 2
Tank Adapter Nuts
; are in place and (
*
=oiled) (see below and
schematics on pages 11–12 for details as needed).
❏
❏
❏
❏
❏
Non-E-Trigger
TM
Markers go to STEP 2) on page 19
.
For E-Trigger
TM
Markers:
Do not operate sear tripper assembly uninstalled as solenoid /
armature may pinch you.
E-Trigger
TM
Parts Not Shown
in Basic Parts List on
(pages 12-13)
TA06020 Armature Pin
TA09935
Electronics
Assembly
TA05014 Magnet
Solenoid
-Armature
02-88
Sear Spring
TA01135 Sear
STEP 2:
❏
Carefully install the left receiver half (make sure halves fit flush).
❏
Insert 4 short receiver bolts
.
❏
If marker has a barrel shroud - insert it now.
❏
Insert 3 long receiver bolts
and
❏
Tighten the 7 bolts /
.
❏
Attach adapter
tighten
2 bolts
(NOTE: short adapter
bolt goes in front).
❏
Apply marker oil onto the barrel o-ring, insert
the barrel
and carefully screw it in.
❏
Slide the feed elbow into the receiver and tilt up until the feed lock
holds it in place.
❏
E-Trigger
TM
Markers - Attach a 9 volt battery to the
battery connector and be sure the wires lay flat inside
the cutout area of the receiver.
❏
Carefully tilt and insert the battery (wire attached
end first
) into the receiver.
❏
Install the left receiver grip
with 2 bolts
.
❏
Press in the 2 magazine tabs
and slide the
magazine
up into the marker until the tabs
lock it in place.
NOTE: The magazine may be used
to store tools and lubricating oil for your marker
(shown with 2 allen wrenches
and oil).
Reassembling Receiver Halves:
(continued on page 19)
❏
Double check that the E-Trigger
TM
Parts
are Positioned correctly for Reassembly
as follows:
❏
1)
Place solenoid / (armature - fits
inside solenoid) into right receiver.
❏
2)
Carefully align and insert the
electronics board
into slot.
❏
3)
Place trigger switch on two pins
of right receiver half.
❏
4)
Insert capacitor in slot.
❏
5)
Route wires in cutout areas to lay flat under armature pin and
battery and not be pinched when receiver halves are reassembled.
❏
Visually inspect internal wires for disconnected wire end(s) or
damage.
❏
6)
Insert armature pin into 2 slots so it moves freely.
❏
7)
Insert Magnet
in slot below armature as shown.
❏
Double check that all parts are in place as shown.
❏
Place battery connector
through left receiver half
❏
make
sure the magnet fits into left receiver half slot so it does not break
and
❏
wires are not pinched as you
❏
place left half on right half so
the halves fit flush.
(E-Trigger
TM
Markers Go to STEP 2 on page 19).
Marker Disassembly / Assembly
(continued from page 17)
Carefully hand start
all threaded parts and
do not overtighten and strip threaded parts when assembling.
Reassembling Receiver Halves:
(continued from page 18)
