7
E
N
G
L
I
S
H
For Tactical Edition models:
(continued from page 6)
6
Safety Is Your Responsibility
(continued from page 5)
For Tactical Edition models:
(continued on page 7)
STEP 2) Air Supply Cylinder Installation
• Do not pressurize a partially assembled paintball marker.
• First install barrel sleeve (see instructions on page 2).
• Next put trigger safety in Safe Mode
(see instructions on page 4).
❏
Eye protection designed for paintball use must be worn by the user
and any person within range. Do not disassemble this marker while it is
pressurized with air. Do not pressurize a partially assembled marker.
• To install the air supply cylinder, lubricate the cylinder valve o-ring
with a little marker oil then insert the cylinder valve end into the air
supply adapter at the back end of the marker grip. Twist the cylinder
clockwise
into the marker until it stops. Your marker is ready to
fire once you switch to Fire Mode from Safe Mode. If the tank is full
and you do not hear the air supply engage, the pin valve could be too
short or the pin valve seal is damaged.
• Next you need to cock the marker
by sliding the bolt handle all the
way back until it locks into place .
Always keep marker in the cocked
position when air supply is attached
to the marker. This will help prevent
an accidental discharge.
•
Install the shroud
before you install the barrel . To install the
shroud:
❏
❏
❏
❏
❏
Remove receiver bolt
and
❏
❏
❏
❏
❏
insert the shroud.
❏
❏
❏
❏
❏
Replace and tighten the bolt
to hold the shroud in place.
• Install the barrel (with the shroud installed):
❏
apply marker oil onto
the barrel o-ring
, insert the barrel into the shroud / receiver and
carefully screw it in .
E
N
G
L
I
S
H
Read each step completely before performing the step:
NOTE: Carefully hand start all threaded parts and do not overtighten and
strip threaded parts when assembling.
❏
❏
❏
❏
❏
For Alpha Black
TM
Basic models
:
•
Install the barrel .
❏
Apply marker oil onto the barrel o-ring ,
insert the barrel into the receiver and carefully screw it in .
• Avoid alcoholic beverages before and during the use of this marker.
Handling markers while under the influence of drugs or alcohol is a
criminal disregard for public safety.
• Avoid shooting an opponent at point blank, 6 feet or less.
• Familiarize yourself with instructions listed on air supply cylinder or adaptor.
Contact the air supply cylinder or adaptor manufacturer with any questions.
• Always measure your marker’s velocity before playing paintball and
never shoot at velocities in excess of 300 feet per second (see
instructions on page 8).
STEP 1) Prepare Marker for Air Supply Cylinder Installation
• For Basic marker with E-Trigger
TM
- You must first read and follow
E-Trigger
TM
Operating Instructions (on pages 8 - 10) before
performing STEP 2 on page 7.
• For Basic marker without E-Trigger
TM
go to STEP 2 on page 7.
• For Tactical Edition marker with E-Trigger
TM
- You must first read and
follow E-Trigger
TM
Operating Instructions (on pages 8-10) before
performing STEP 2.
• For Tactical Edition marker without E-Trigger
TM
go to STEP 2.
• For Alpha Black
TM
Tactical Edition models
:
Squeeze the
adjustment lever
and slide to shorten
or to lengthen stock.
Shorten
Lengthen
Length
Adjustment:
•
Install the collapsible stock.
❏
❏
❏
❏
❏
With the end cap cover
removed (slides off).
❏
❏
❏
❏
❏
Slide stock up
into end cap.
❏
❏
❏
❏
❏
Insert bolt
and carefully tighten .
STEP 3) Hopper Installation
• Barrel Sleeve must be installed (see page 2) and safety in Safe Mode
(see page 4) before filling the hopper.
• Make sure that the feed elbow and hopper are clean and free of any
sharp edges to keep paintballs feeding into the marker smoothly.
• Install the hopper neck into the feed elbow of your marker and
tighten the hopper down with a 3/16” allen wrench
included
with your marker.
NOTE: Do not overtighten or the elbow may break. With the barrel
Hopper Installation
(continued on page 8)
GETTING STARTED
7
E
N
G
L
I
S
H
For Tactical Edition models:
(continued from page 6)
6
Safety Is Your Responsibility
(continued from page 5)
For Tactical Edition models:
(continued on page 7)
STEP 2) Air Supply Cylinder Installation
• Do not pressurize a partially assembled paintball marker.
• First install barrel sleeve (see instructions on page 2).
• Next put trigger safety in Safe Mode
(see instructions on page 4).
❏
Eye protection designed for paintball use must be worn by the user
and any person within range. Do not disassemble this marker while it is
pressurized with air. Do not pressurize a partially assembled marker.
• To install the air supply cylinder, lubricate the cylinder valve o-ring
with a little marker oil then insert the cylinder valve end into the air
supply adapter at the back end of the marker grip. Twist the cylinder
clockwise
into the marker until it stops. Your marker is ready to
fire once you switch to Fire Mode from Safe Mode. If the tank is full
and you do not hear the air supply engage, the pin valve could be too
short or the pin valve seal is damaged.
• Next you need to cock the marker
by sliding the bolt handle all the
way back until it locks into place .
Always keep marker in the cocked
position when air supply is attached
to the marker. This will help prevent
an accidental discharge.
•
Install the shroud
before you install the barrel . To install the
shroud:
❏
❏
❏
❏
❏
Remove receiver bolt
and
❏
❏
❏
❏
❏
insert the shroud.
❏
❏
❏
❏
❏
Replace and tighten the bolt
to hold the shroud in place.
• Install the barrel (with the shroud installed):
❏
apply marker oil onto
the barrel o-ring
, insert the barrel into the shroud / receiver and
carefully screw it in .
E
N
G
L
I
S
H
Read each step completely before performing the step:
NOTE: Carefully hand start all threaded parts and do not overtighten and
strip threaded parts when assembling.
❏
❏
❏
❏
❏
For Alpha Black
TM
Basic models
:
•
Install the barrel .
❏
Apply marker oil onto the barrel o-ring ,
insert the barrel into the receiver and carefully screw it in .
• Avoid alcoholic beverages before and during the use of this marker.
Handling markers while under the influence of drugs or alcohol is a
criminal disregard for public safety.
• Avoid shooting an opponent at point blank, 6 feet or less.
• Familiarize yourself with instructions listed on air supply cylinder or adaptor.
Contact the air supply cylinder or adaptor manufacturer with any questions.
• Always measure your marker’s velocity before playing paintball and
never shoot at velocities in excess of 300 feet per second (see
instructions on page 8).
STEP 1) Prepare Marker for Air Supply Cylinder Installation
• For Basic marker with E-Trigger
TM
- You must first read and follow
E-Trigger
TM
Operating Instructions (on pages 8 - 10) before
performing STEP 2 on page 7.
• For Basic marker without E-Trigger
TM
go to STEP 2 on page 7.
• For Tactical Edition marker with E-Trigger
TM
- You must first read and
follow E-Trigger
TM
Operating Instructions (on pages 8-10) before
performing STEP 2.
• For Tactical Edition marker without E-Trigger
TM
go to STEP 2.
• For Alpha Black
TM
Tactical Edition models
:
Squeeze the
adjustment lever
and slide to shorten
or to lengthen stock.
Shorten
Lengthen
Length
Adjustment:
•
Install the collapsible stock.
❏
❏
❏
❏
❏
With the end cap cover
removed (slides off).
❏
❏
❏
❏
❏
Slide stock up
into end cap.
❏
❏
❏
❏
❏
Insert bolt
and carefully tighten .
STEP 3) Hopper Installation
• Barrel Sleeve must be installed (see page 2) and safety in Safe Mode
(see page 4) before filling the hopper.
• Make sure that the feed elbow and hopper are clean and free of any
sharp edges to keep paintballs feeding into the marker smoothly.
• Install the hopper neck into the feed elbow of your marker and
tighten the hopper down with a 3/16” allen wrench
included
with your marker.
NOTE: Do not overtighten or the elbow may break. With the barrel
Hopper Installation
(continued on page 8)
GETTING STARTED
