ThyssenKrupp DAF 330 Operating Manual Download Page 45 | Manualshive

Page: 45 / 52

ThyssenKrupp DAF 330 Operating Manual Download Page 45

O

PERATING

M

ANUAL

9.

A

NNEX

ThyssenKrupp Aufzugswerke GmbH

9.3 C

ONNECTING CABLE FOR PULSE GENERATOR

Pulse generator cable – technical data
(suitable for make: Stegmann / type 1024 / 4096 pulses / HTL and TTL)

connecting socket to motor                         plug details                                                controller connector
pre-installed connection to                          (terminal end cable / solder side)              compatible with
pulse generator                                                                                                               MFC 16 and MFC 20

socket

connector / motor

connector / MFC

Nr. 65 960 60 890
cable for controller
shielded cable

wire colour

brown
green

grey
pink

red
black

white-green
POWER SUPPLY
brown-green

Drahtfarbe

Reglerstecker

MFC-16 u. MFC-20
kompatibel

controller connector

compatible with
MFC-16 and MFC-20

wire
colour

45

Version 02/2009

DAF330

«
...
43
44
45
46
47
...
»

Summary of Contents for DAF 330





















































Reviews:

No comments