manualshive.com logo in svg

ThyssenKrupp DAF 330, Operating Manual, Page: 35 / 52

Share
Download
ThyssenKrupp DAF 330 Operating Manual Download Page 35

O

PERATING 

M

ANUAL

 

 

7.

 

M

AINTENANCE

 

 

ThyssenKrupp Aufzugswerke GmbH 

 

 7.4 

Adjusting of brake test switch 

 

Adjust brake shoe stroke before you start adjusting the sensors! For 
description see chapter 7.2 

 

Adjusting : 

1.  Switch on emergency electrical operation switch and lift control. 
2.  Reset adjusting screw (fig. 14 pos. 6) towards switch until LED flickers. 
3.  Slowly turn back screw until LED goes out. 
4.  Reset adjusting bolt by one fourth of a rotation (equivalent to approx.    

0.3 mm) towards the switch and lock it. 

 

LED flickers constantly. 

5. 

Check adjustment:

  

Release and close brakes by connecting the motor. Check the functioning 
of the sensors when varying between brake applied and disengaged.  
 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

1 

Adjusting screw stroke 

2 

Joint 

3 

Brake magnet 

4 

Lamp (LED) 

5 

Brake test switch 

6 

Button (sensor) 

7 

Adjusting screw brake test 

8 

Adjusting screw resilience 

 

Fig. 14 

 

1 

2 

3 

8 

7 

6 

5 

4 

35

Version 02/2009

DAF330

Summary of Contents for DAF 330





















































Reviews:

No comments