THORLABS M2MS Operating Manual Download Page 129

Page: 129 / 167

BP209 Series

7 Operation Instructions

Rev: 8.1, 14-Feb-2022

Page 127

7.2.8.6 Divergence Measurement Results

The green bulb indicates that the measurement was successful.

These values can also be found in the listing of the complete

Results

Negative values indicate a converging beam, while positive values indicate a diverging beam.

Note

All results are calculated from the applied linear fit!

Full Divergence Angle X' (Y')

is explained in chapter

M² Theory

Divergence Asymmetry

Asymmetry is the quotient of divergence angles in Y and X scan direc-

tions. Values differing from 1.0 indicate that the beam ellipticity is changing with z position, for
instance an elliptical beam is focused to a round spot.

130

Summary of Contents for M2MS







































































































































































Search results

Summary of Contents for M2MS

Reviews:

Related manuals for M2MS

Brands by name

Popular brands

THORLABS M2MS, Operating Manual

Search results

Summary of Contents for M2MS

Reviews:

Related manuals for M2MS

Brands by name

Popular brands