THORLABS M2MS Operating Manual Download Page 59

Page: 59 / 167

BP209 Series

6 The Graphics User Interface (GUI)

Rev: 8.1, 14-Feb-2022

Page 57

6.6.9.2 Plot Power

Toolbar:

, Menu bar: Windows -> Plot Power

The total power measured by the Beam Profiler vs. time can be displayed.

Note

The power indication of Thorlabs Beam Profiler instruments is not calibrated vs. wavelength, it
is based on a typical responsivity curve of the used photo diode and the manually entered
wavelength (see

Optical Setup / Wavelength

)

Toolbar Icon

Associated Action

Save Diagram or Image: Opens a dialog box to specify the properties of the
saved diagram or image.

Save Data: Opens a dialog box to specify the properties of the saved calcu-
lation data.

Clear all plots

Show or Hide the grid in the diagram:

Autoscale ON/OFF

Show or hide the cursor

Summary of Contents for M2MS







































































































































































Search results

Summary of Contents for M2MS

Reviews:

Related manuals for M2MS

Brands by name

Popular brands

THORLABS M2MS, Operating Manual

Search results

Summary of Contents for M2MS

Reviews:

Related manuals for M2MS

Brands by name

Popular brands