Thermo Scientific Dionex Easion Operator'S Manual Download Page 56

Page: 56 / 126

Dionex Easion Operator’s Manual

Doc. 155028-01 08/20

The table below lists the Dionex Easion-related error messages, as well as their
default severity levels. For troubleshooting assistance, go to the page indicated in
the table.

If this error occurs when you turn on the Dionex Easion power, you can
disregard it. If the error occurs at other times, it should be resolved.

To troubleshoot:

Refer to the suppressor manual for troubleshooting procedures.

This error occurs if you try to calibrate the flow rate while the pump is off, or
while the pump is on but the flow rate is not 1 mL/min.

To troubleshoot:

Be sure to click

Start Calibration

on the Wellness panel with the flow rate

calibration instructions. This automatically starts the pump and sets the flow
rate to 1 mL/min. For flow rate calibration instructions, see

Section 5.1.3

Audit Trail Error Message

Default
Severity Level

See

Conductivity exceeds limit.

Warning

page 48

Flow rate calibration error.

Warning

page 48

Load/inject valve error.

Error

page 49

Module data buffer overflow. Data may have been
lost.

Warning

page 49

Pump motor lost control.

Warning

page 49

Pump pressure hardware error.

Warning

page 49

Pump pressure slope calibration error.

Warning

page 50

Remaining eluent below 100 mL.

Error

page 50

Remaining eluent below 200 mL.

Error

page 50

The system pressure has exceeded the high
pressure limit.

Abort

page 51

The system pressure is below the low pressure limit.

Abort

page 51

Conductivity exceeds limit.

Flow rate calibration error.

Summary of Contents for Dionex Easion































































































































Search results

Summary of Contents for Dionex Easion

Reviews:

Related manuals for Dionex Easion

Brands by name

Popular brands

Thermo Scientific Dionex Easion, Operator'S Manual

Search results

Summary of Contents for Dionex Easion

Reviews:

Related manuals for Dionex Easion

Brands by name

Popular brands