manualshive.com logo in svg

Thermo Scientific Dionex Easion, Operator'S Manual, Page: 40 / 126

Share
Download
Thermo Scientific Dionex Easion Operator'S Manual Download Page 40

Dionex Easion Operator’s Manual

32

Doc. 155028-01 08/20

4. Click 

Prime

 on the Chromeleon ePanel (see 

Figure 2-10

).

–or–

Open the Command window (by pressing the 

F8 

key), select the 

Pump

 

command, and select the 

Prime

 option. 

5. The pump will begin pumping at about 3 mL/min. Continue priming the 

Dionex Easion until no air bubbles are exiting the pump waste line.

6. Click the pump 

Off

 button on the Chromeleon ePanel.

7. Close the waste valve. 

Do not overtighten.

 The pump is now ready for 

operation.

NOTE A convenient way to verify that the waste valve is closed

is to select the pump flow rate required for your
application, turn on the pump, and then close the valve.
The pressure should rise to the value expected for the
application and quickly stabilize.

Figure 3-3.  Priming the Pump

Waste Valve

(Open)

Secondary

Pump Head

Summary of Contents for Dionex Easion































































































































Reviews:

No comments