Thermo Scientific Dionex Easion Operator'S Manual Download Page 65

Page: 65 / 126

4 • Troubleshooting

Doc. 155028-01 08/20

•

No flow from pump

There are several possible causes for this issue; for more information, see

Section 4.4

and

Section 4.5

•

Cell electronics malfunctioning

Use the Wellness panel to test the electronics with a dummy cell. (For
instructions, see

Section 5.1

and the Chromeleon Help.) If the conductivity

reading with the dummy cell is outside the tolerance range, the electronics are
malfunctioning. Contact Technical Support for Dionex products for
assistance. The Dionex Easion electronics components cannot be serviced by
the user.

4.12 High Detector Output

•

Background not suppressed by suppressor

Conductivity exceeds limit

is displayed in the Chromeleon audit trail, refer

to the suppressor manual for troubleshooting procedures.

•

Sample concentration too high

Dilute the sample (see

Section 3.10.3

•

Wrong eluent or regenerant

Check that you are using the correct eluent (see

) for your system.

•

Cell out of calibration

Contact Technical Support for Dionex products for assistance.

4.13 Baseline Noise or Drift

•

Flow system leak; erratic baseline

Check all fittings and liquid lines for leaks. Tighten or, if necessary, replace
all liquid line connections. Refer to

Installation of Dionex Liquid Line Fittings

(Document No. 031432) for tightening requirements.

Summary of Contents for Dionex Easion































































































































Search results

Summary of Contents for Dionex Easion

Reviews:

Related manuals for Dionex Easion

Brands by name

Popular brands

Thermo Scientific Dionex Easion, Operator'S Manual

Search results

Summary of Contents for Dionex Easion

Reviews:

Related manuals for Dionex Easion

Brands by name

Popular brands