thermital SUNDAY 30/130 B Installation And Maintenance Manual Download

Page: 54 / 56

ENGLISH

TECHNICAL ASSISTANCE SERVICE

CAUSE

FAULT

SOLUTION

Burner dirty.

Insufficient air/fuel flow to burner.

Incorrect temperature setting.

The boiler does not reach its

temperature set point.

Clean the combustion chamber.

Check and adjust the burner.

Adjust the temperature setting
and check on correct functioning.
Verify the temperature setting.

No water supply.

Wrong boiler temperature
setting.

Incorrectly positioned sensors.

Sensors malfunctioning/faulty.

Burner locks out.

Check the vent and bleed valves.
Check CH circuit pressure.

Verify the temperature setting.

Check positioning of sensors.

Check correct functioning of
sensors and electrical cables.

Air in the circuit.

Pump malfunctioning.

Boiler reaches set

temperature but radiators are

still cold.

Bleed the circuit.

Unseize the pump.
Change the pump.
Check pump electrical
connections.

Pump malfunctioning.

Pump does not start.

Unseize the pump.
Change the pump.
Check pump electrical
connections.

Problem with CH circuit
expansion vessel.

Circuit pressure too high.

Safety valve incorrectly
calibrated or faulty.

The safety valve keeps

opening.

Check efficiency of expansion
vessel.

Check circuit pressure.
Check pressure reducer.

Check valve setting and efficiency.

Summary of Contents for SUNDAY 30/130 B

























































Search results

Summary of Contents for SUNDAY 30/130 B

Reviews:

Related manuals for SUNDAY 30/130 B

Brands by name

Popular brands

thermital SUNDAY 30/130 B, Installation And Maintenance Manual

Search results

Summary of Contents for SUNDAY 30/130 B

Reviews:

Related manuals for SUNDAY 30/130 B

Brands by name

Popular brands