thermital SUNDAY 30/130 B Installation And Maintenance Manual Download | Manualshive

Page: 49 / 56

background image

49

ENGLISH

TECHNICAL ASSISTANCE SERVICE

20

40 60 80

100

4

3 2 1

0

0

120

Min. gas

power screw

Max. gas

power screw

ADJUSTING THE GAS VALVE

- Switch on mains power to the boiler.
- Open the gas cock.
- Turn the function selector to OFF/RESET (the display

shows “

- -

”)

- Pull off the DHW temperature selector knob (2) and the

function selector knob (6)

-

Perform the procedure given above to activate the

“combustion analysis” phase

- Wait for the burner to ignite. The display will read out

“CO” and the boiler will start functioning at maximum
central heating power. The chimney sweep function
remains active for a maximum time of 15 minutes. If the
central heating flow reaches a temperature of 85°C, the
burner shuts down. The burner will re-ignite when cen-
tral heating flow temperature drops below 75°C.

- Remove the cap and insert the combustion analysis

probe

- Turn the Max CH trimmer clockwise until maximum fan

speed is reached (see table)

6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30

6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30

Rated heat input, CH mode (kW)

COnoair curve (Qnheating) – 30 kW

Heating curve (Qnheating) – 30 kW

Fan speed in CH mode (rpm

)

1300

1700

2100

2500

2900

3300

3700

4100

4500

4900

5300

5700

6100

Rated heat input, CH mode (kW)

10

20

30

40

50

60

70

80

90

100

110

120

130

140

150

160

170

180

190

200

COnoair (p.p.m.) G20

30/130 B

b

Setting changes do not cause the burner to ignite. As you turn the trimmer, a value expressed in thousands (e.g.
2.5 = 2500 rpm) automatically appears on the 2 digit display.

When supplied, the boiler is configured with the settings shown in the table below. These settings can be changed if
necessary to comply with specific system requirements or regional emission control legislation. Refer to the following
graphs to adjust the settings.

«
...
47
48
49
50
51
...
»

Summary of Contents for SUNDAY 30/130 B

























































Reviews:

No comments

Related manuals for SUNDAY 30/130 B

Brand: ideal commercial Pages: 6

Brand: Alpha Pages: 4

Brand: Hamworthy Pages: 42

Brand: THERMOSTAHL Pages: 27

turboMAX pro 24/2 E

Brand: Vaillant Pages: 44

Brand: Fondital Pages: 64

Brand: Mikrofill Pages: 29

Potterton Suprima 30 HE

Brand: Baxi Pages: 8

Luna Platinum 1.12

Brand: Baxi Pages: 37

Mainfour 24-24F

Brand: Baxi Pages: 204

Brand: Sime Pages: 104

Brand: Sime Pages: 104

Brand: Immergas Pages: 148

VICTRIX 115 1 I

Brand: Immergas Pages: 146

Bryan DR Series

Brand: Bryan Boilers Pages: 2

Bryan Knockdown CLM-120 29

Brand: Bryan Boilers Pages: 4

A-H-FS-15-12-50-D operati

Brand: Bryan Boilers Pages: 17

Brand: Truma Pages: 94

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands