thermital SUNDAY 30/130 B Installation And Maintenance Manual Download

Page: 43 / 56

ENGLISH

TECHNICAL ASSISTANCE SERVICE

WARNING LEDS AND ERRORS

THE MAIN CONTROL PANEL
Green LED (2)

Off =

boiler in stand-by, burner out

On =

burning lit, boiler functioning normally.

Red LED (3)

Safety shutdown:

an error code flashes on the display.

Burner lockout:

the red LED lights and an error code

flashes on the display.
No error code is shown in OFF/RESET mode (

). To visual-

ise any system errors, turn the function selector to "".

Error codes are displayed normally in combustion analy-
sis and frost protection modes.

To restore normal functioning, turn the function selector
to “

” (OFF/RESET) then return it to Summer position "".

If the boiler does not restart after a number of resets, call
your local Technical Assistance Centre.

Boiler control card alarms

CODE

DESCRIPTION OF ERROR

STATUS

AL10

Ignition attempts finished (no flame/condensate detected)

Lockout

AL20

Temperature threshold error

Lockout

AL21

Low temperature thermostat/condensate pump safety error

Lockout

AL29

Flue gas sensor overtemperature error

Lockout

AL60

Storage cylinder temperature sensor error

Signalling

AL71

CH flow temperature sensor error (open/short circuit)

Shutdown

AL73

CH return temperature sensor error (open/short circuit)

Shutdown

AL74

Overtemperature for no water circulation

Lockout

AL91

Primary heat exchanger needs cleaning (call Technical Assistance)

Signalling

AL28

CH flow/return sensors temperature differential error

Lockout

AL26

CH return overtemperature

Lockout

AL79

CH flow overtemperature, or flow/return sensors temperature differential error

Lockout

AL41

Low CH water pressure

Shutdown

AL40

Low CH water pressure (after 10 minutes)

Lockout

AL34

Fan speed error

Lockout

AL52

Generic electronic error

Lockout

AL55

Boiler configuration error (configuration jumper missing)

Lockout

40 60 80

100

3 2 1

120

40 60 80

100

3 2 1

120

°C

120

100

Summary of Contents for SUNDAY 30/130 B

























































Search results

Summary of Contents for SUNDAY 30/130 B

Reviews:

Related manuals for SUNDAY 30/130 B

Brands by name

Popular brands

thermital SUNDAY 30/130 B, Installation And Maintenance Manual

Search results

Summary of Contents for SUNDAY 30/130 B

Reviews:

Related manuals for SUNDAY 30/130 B

Brands by name

Popular brands