thermital SUNDAY 30/130 B Installation And Maintenance Manual Download | Manualshive

Page: 21 / 56

background image

21

ENGLISH

INSTALLER

UNPACKING THE PRODUCT

The boiler is delivered in a single package on a wooden
pallet, covered by a PVC sheet and inside a wooden
crate.
The following items are delivered in a plastic bag (A)
inside the boiler:

- User manual
- Installation and maintenance manual
- Spare parts catalogue
- Warranty certificate
- Hydraulic test certificate
- LPG conversion kit (diaphragm, label)
- Outdoor temperature sensor.

b

The instruction manuals are integral parts of the
boiler. Once located, read them thoroughly and
keep them safe.

Description

L

600

mm

P

610

mm

H

1540

mm

Net weight

130

Kg

A

SUNDAY 30/130 B

boilers are designed and made for

installation in combined central heating and domestic hot
water production systems.

H

P

L

DIMENSIONS AND WEIGHT

«
...
19
20
21
22
23
...
»

Summary of Contents for SUNDAY 30/130 B

























































Reviews:

No comments

Related manuals for SUNDAY 30/130 B

NEOTHERM NTH Series

Brand: Laars Pages: 84

Brand: AJAX Pages: 116

Brand: DeDietrich Pages: 40

Brand: Easylife Pages: 4

Brand: CleaverBrooks Pages: 314

CHITWOOD SMOKE BROILER KC-24

Brand: Jade Pages: 10

Brand: Olsen Pages: 84

Brand: Halstead Pages: 20

Brand: LAMBORGHINI Pages: 48

VITORONDENS 200-T

Brand: Viessmann Pages: 32

Vitorond 200 Series

Brand: Viessmann Pages: 28

Brand: Viessmann Pages: 32

VITORADIAL 300-T

Brand: Viessmann Pages: 48

VITOLIGNO 300-P

Brand: Viessmann Pages: 60

VITODENS 200 WB2B

Brand: Viessmann Pages: 4

Brand: Viessmann Pages: 4

Vitodens 100 WB1A

Brand: Viessmann Pages: 4

Brand: Viessmann Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands