thermital SUNDAY 30/130 B Installation And Maintenance Manual Download Page 2 | Manualshive

Page: 2 / 56

background image

2

ENGLISH

CONFORMITY

THERMITAL SUNDAY 30/130 B

boilers conform to the following directives:

• Directive 92/42/EEC on efficiency requirements
• Directive 2009/142/EC - Gas Appliances
• Low Voltage Directive 2014/35/EU
• Electromagnetic Compatibility Directive 2014/30/EU
• Ecodesign Directive 2009/125/CE for energy-related products
• Energy Labelling Directive 2010/30/EU
• Delegated Regulation (EU) N. 811/2013
• Delegated Regulation (EU) N. 813/2013
• Delegated Regulation (EU) N. 814/2013
• EN 677 Standard: Gas-fired central heating boilers; specific requirements
for condensing boilers with a nominal heat input not exceeding 70 kW

MODELL

CODE

SUNDAY 30/130 B

20105842

RANGE

RANGE RATED

This boiler is RANGE RATED. That means it is fitted with a device that adjusts its heat output to suit the requirements
of the heating system and therefore the thermal energy needs of the building.
See the “Settings” section for information on system calibration.

ACCESSORIES

For a complete list of accessories and details of their compatibility, refer to the Catalogue.

«
1
2
3
4
...
»

Summary of Contents for SUNDAY 30/130 B

























































Reviews:

No comments

Related manuals for SUNDAY 30/130 B

Brand: Laars Pages: 9

ecoMAX pro 28 E

Brand: Vaillant Pages: 36

Brand: Daikin Pages: 12

Brand: Wahl Bach Pages: 52

Rotex A1 BO Series

Brand: Daikin Pages: 60

Brand: IBC Pages: 78

Brand: Lamborghini Caloreclima Pages: 52

Vitocrossal 300 CR3

Brand: Viessmann Pages: 48

Brand: Navien Pages: 29

BlueHelix ALPHA C

Brand: ferolli Pages: 320

THERMIFIC MODU-FIRE

Brand: Patterson-Kelley Pages: 27

Brand: Crestron Pages: 60

Brand: Crest Audio Pages: 24

WarmMaster DeLuxe

Brand: kochstar Pages: 12

Brand: Nature's Comfort Pages: 30

Brand: Ideal Boilers Pages: 72

Brand: Potterton Pages: 8

Brand: BENEKOV Pages: 39

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands