7
By rear tillers, ensure that the blades are protected by
safety shield, only the part of the blades that works into
the soil must be free.
Never attempt to make any adjustments, while the
engine is running.
Use extreme caution when reversing or pulling the
machine backwards
Never operate the engine indoor or in areas with low
ventilation. The exhaustion from the engine contains
carbon monoxide. Failure to observe could result in
permanent injury or death.
Gasoline safety
Use extreme care in handling gasoline. Gasoline is
extremely flammable and the fumes are explosive.
Serious personal injury can occur, when gasoline is
spilled on yourself or your clothes. Rinse your skin and
change clothes immediately!
Use only an approved gasoline container. Do not use
soft drink bottle or similar!
Extinguish all cigarettes, cigars, pipes and other sources
of ignition.
Never refuel your machine indoors.
Let the engine cool down before refilling
Never fill the fuel tank to more than 2.5 cm below bottom
of filler in order to provide space for fuel to expansion.
After refueling, ensure that the cap tighten securely.
Never use the lock-function on the gasoline gun, when
refueling.
Do not smoke while refueling.
Never refuel inside a building or where gasoline fumes
may get in contact with an ignition source.
Keep gasoline and engine away from appliance, pilot
lights, barbecues, electric appliances, power tools, etc.
If the fuel tank has to be drained, this shall be done
outdoors
Maintenance and storage
The engine shall be stopped when carrying out
maintenance and cleaning operations, when changing
tools and when being transported by means other than
under its own power.
Check regularly that all bolts and nuts are tightened.
Retighten if necessary.
The engine must be completely cooled before storing
indoors or covered.
If the machine unused for a period of time, please refer
to the instructions in this manual.
Maintain or replace safety and instruction labels, as
necessary.
Only use original spare parts or accessories. If not
original parts or accessories is used, the liability is no
longer applied.
Replace faulty silencers.
Miscellaneous
The gears are delivered pre-greased. However, always
ensure they are well greased before each use.
The motor is not pre-filled with oil.
Factory-fitted control devices, such as the handle-
mounted clutch cable, must not be removed or exposed.
Only drain the fuel tank outdoors. Gasoline is extremely
flammable and the fumes are explosive.
Ensure that the machine is properly secured when
transported on a flatbed etc.
Reduce the throttle during engine shutdown and close
the fuel valve.
Assembly
1.
Box content
1. Tiller
2. Blade, right/left
3. Upper handle section
4. Lower handle section x2
5. Handle assembly mounting
6. Plastic guard w/ clips
7. Cable holders
8. Front carrying handle
9. Blade guard, right/left
10. Wheel bushing
11. Depth skid w/ split pin
12. Mounting kit for upper handle section
13. Manual
2.
Fig 1. Attach the wheels. Use the supplied parts shown.
3.
Fig 2. Fit the blade guards. Use the supplied bolts.
The left and right guards are different.
4.
Fig 3. Fit the blades. Ensure the sharp edges of the
blades face forward.
The left and right blades are different.
5.
Fig 4. Fit the lower handle section. Use the supplied
mountings and bolts.
6.
Fig 5. Fit the upper handle section. Use the supplied
assembly kit as shown.
7.
Fig 6. Fit the cover using four of the supplied clips.
8.
Fig 7. Fit the cover behind the lower handle using four
more of the supplied clips.
9.
Fig 8. Fit the clutch lever. Ensure the lever is level with
the lower edge of the handle as shown.
The cable feeding through upper plastic guard should be
fitted to the right side of the lever.
The cable feeding through the rear plastic guard should
be fitted to the left side of the lever. Ensure the levers
are fitted correctly.
10.
Fig 9. Fit the throttle lever to the right side of the handle.
Fit the cable holders. Use the supplied cable holders to
secure the cables.
11.
Fig 10. Fit the depth skid. Secure with the supplied split
pin.
12.
Fig 11. Fit the rear bracket. Use the supplied nuts and
bolts. Secure attached accessories using the supplied
bolts and split pins
Fill the motor with oil. See changing the oil section for
more details
.
Clothing
When using the machine, wear close-fitting work clothes,
hard-wearing work gloves, ear defenders and non-slip boots
with steel toecaps.
Summary of Contents for LX550B
